Publicidad
Idiomas disponibles
Idiomas disponibles
MAINTENANCE
Check wires and connections to be sure corrosion is not adding additional resistance to the motor circuit and causing a low voltage condition
at the motor. Low voltage can inhibit motor from starting and cause fuse to blow. Full voltage should be available to prevent motor
damage.
NOTICE: If pump is idle for extended periods, the impeller may stick to the pump body, preventing motor rotation and causing blown fuses.
To correct, remove end cover and impeller, clean body and impeller, then lubricate with water or small amounts of grease before assembly.
If pump is to be in freezing temperatures, drain by loosening end cover screws.
A spare impeller should be carried aboard to be assured of pumping capability.
DISASSEMBLY
1. Remove end cover screws, end cover and O-ring.
2. Withdraw impeller.
3. Loosen and remove two slotted hex screws, which attach body
to motor.
4. Tap body lightly between ports and remove body from motor.
5. With a 1/2" (12.7mm) diameter dowel, push against the shaft
seal from back (motor) side of the body to dislodge it from
the seal bore.
NOTE: Do not tamper with or disassemble motor.
DIMENSIONAL DRAWING
DESSIN DIMENSIONNEL pouces (millimètres) / MASSZEICHNUNG Zoll (Millimeter) / DISEGNO DIMENSIONALE Pollici (millimetri) /
MAAT TEKENING Inch (millimeter) / DIMENSIONELL RITNING tum (millimeter) / DIBUJO DIMENSIONAL Pulgadas (milímetros)
NOTICE: END OF LIFE PRODUCT DISPOSAL.
Handle and dispose of all waste in compliance with local laws and regulations.
WARRANTY
XYLEM LIMITED WARRANTY WARRANTS THIS PRODUCT TO BE FREE OF DEFECTS AND WORKMANSHIP FOR A PERIOD OF 1 YEAR FROM DATE OF MANUFACTURE. THE
WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES, GUARANTEES, CONDITIONS OR TERMS OF WHATEVER NATURE RELATING
TO THE GOODS PROVIDED HEREUNDER, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
WHICH ARE HEREBY EXPRESSLY DISCLAIMED AND EXCLUDED. EXCEPT AS OTHERWISE PROVIDED BY LAW, BUYER'S EXCLUSIVE REMEDY AND SELLER'S AGGREGATE LIABILITY
FOR BREACH OF ANY OF THE FOREGOING WARRANTIES ARE LIMITED TO REPAIRING OR REPLACING THE PRODUCT AND SHALL IN ALL CASES BE LIMITED TO THE AMOUNT PAID
BY THE BUYER HEREUNDER. IN NO EVENT IS SELLER LIABLE FOR ANY OTHER FORM OF DAMAGES, WHETHER DIRECT, INDIRECT, LIQUIDATED, INCIDENTAL, CONSEQUENTIAL,
PUNITIVE, EXEMPLARY OR SPECIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOSS OF PROFIT, LOSS OF ANTICIPATED SAVINGS OR REVENUE, LOSS OF INCOME, LOSS OF
BUSINESS, LOSS OF PRODUCTION, LOSS OF OPPORTUNITY OR LOSS OF REPUTATION. THIS WARRANTY IS ONLY A REPRESENTATION OF THE COMPLETE LIMITED WARRANTY.
FOR A DETAILED EXPLANATION, PLEASE VISIT US AT www.xylem.com/en-us/support/, CALL OUR OFFICE NUMBER LISTED, OR WRITE A LETTER TO YOUR REGIONAL OFFICE.
RETURN PROCEDURE
Warranty returns are conducted through the place of purchase. Please contact the appropriate entity with a receipt of purchase to verify date.
Inches (millimeters)
6.06
(153.92)
2.00
1.96
(50.8)
(49.78)
ASSEMBLY
1. Lubricate seal with water and position it in seal bore with lip, or
hollowed-out side of seal, pointing towards the impeller bore.
With a 1/2" (12.7mm) diameter dowel, push against the shaft
seal into its bore until it contacts the bottom.
2. Lubricate motor shaft and install body on motor.
3. Lubricate impeller bore and, aligning flat in impeller with flat
on motor shaft, install impeller with clockwise rotary motion.
4. Install O-ring, end cover and screws.
2X 1/2-14 NPT
(FEMALE)
3.25 (82.55)
1.73 (43.94)
4
DISCHARGE
4.72
(119.88)
2.36
(59.94)
J J
A A
B B
S S
C C
O O
1.78
(45.21)
3.56
(90.42)
Publicidad
