Stiga BC 500 Li 48 Manual De Instrucciones página 176

Action
1. Start the machine
(para. 6.3 );
2. operate the throttle
control lever (Fig. 12.A
Fig. 13.A) and throttle
safety lever (Fig.
12.B, Fig. 13.B) at
the same time;
3. release the throttle
control lever (Fig. 12.A
Fig. 13.A) and throttle
safety lever (Fig.
12.B, Fig. 13.B).
Press only the throttle
control lever (Fig.
12.A, Fig. 13.A).
If any of the results fail to match the
indications provided in the tables below, do
not use the machine! Take it to a service centre
to be checked and repaired if necessary.
6.3 START-UP
6.3.1 Start-up with battery
1. Remove the blade guard (Fig. 1.K) (if used);
2. Make sure the cutting means is not touching
the ground or any other object;
3. insert the battery correctly in its
(Fig. 16) (par. 7.2.3);
4. Press the safety button (Fig. 12.C, Fig. 13.C)
operate the throttle control lever (Fig. 12.A
Fig. 13.A) and throttle safety lever (Fig.
12.B-M, Fig. 13.B-M) at the same time.
6.3.2 Start-up with battery
simulator (if available)
1. Remove the blade guard (Fig. 1.K);
2. Make sure the cutting means is not
touching the ground or any other object;
3. Insert the battery simulator (Fig.
16.P) correctly in its compartment
on the machine (Fig.16.A)
4. connect the connection cable (Fig.
16.O) to the battery simulator
5. select the battery using the
selector (Fig. 11.B)
6. press the safety button
(Fig. 12.C, Fig. 13.C)
7. press the throttle control
(Fig. 12.A, Fig. 13 A)
Result
1. The cutting means
must not move.
2. The cutting means
should move.
3. The levers should
return automatically
and rapidly to the
neutral position and
the cutting means
should stop.
The throttle control lever
remains blocked.
compartment
6.4 OPERATION
NOTE Before starting any tasks for the first
time, get to know the machine, learn the most
suitable cutting techniques, make sure your are
wearing the harness correctly, grip the machine
firmly and make the movements required by the
job.
To use the machine proceed as follows:
– always keep the machine connected to the
correctly worn harness (see par. 6.1.2).
– when working, the machine must always be
firmly held in both hands, keeping the power
unit on the right of the body and the cutting
unit below the line of the belt.
NOTE During use, the battery is protected
against total drainage with a protective device
that switches off the machine and stops it from
working.
NOTE Battery power reserve (and therefore
the cuttable vegetation area before recharging is
required) depends on
(par. 7.2.1).
NOTE After one minute of inactivity, if turned on,
the machine will automatically switch off.
6.4.1 Work techniques
;
6.4.1.a Cutting line head
Use ONLY nylon lines. The use of metal
lines, plastic coated metal lines and/or lines
that are not suitable for the head can cause
serious injuries and wounds.
a. Cutting motion (Scything)
Proceed at a steady pace, with a circular motion
similar to a traditional scythe, without tilting the
cutting line head during the operation (Fig. 17).
Start cutting at the correct height in a small area,
so as to achieve a uniform cutting height keeping
the cutting line head at a constant distance from
the ground.
For heavier cutting it can be useful to tilt the cutting
line head to the left by about 30°.
Do not work in this way if there is the
possibility of causing objects to be thrown,
which could harm people, animals or cause
damage.
EN - 12
many factors described in