Publicidad
Idiomas disponibles
Idiomas disponibles
14. Pull both ends of the cutting line to release them from the
holding slots. If the line extends past the cutting blade on
the guard cut the line so it just reaches the blade.
Replacing Spool Housing (Fig. A, R, S, U)
1. Rotate the spool housing
spindle
lines up with notch
31
third hole
in the motor housing
33
shown in Fig. R. Insert screwdriver through each all three
holes to prevent the spool housing from turning.
2. Turn the spool housing clockwise as shown in Fig. S.
3. Insert a screwdriver back through the three holes
(
,
, and
) and thread the new spool housing
30
32
33
counterclockwise and securely tighten onto the bolt
protruding from the trimmer.
Replacing Spool Assembly (Fig. A, U, V)
1. Rotate the spool housing
spindle plate
36
aligns with notch
Insert a screwdriver through the notch and into the hole,
to prevent the spindle from turning.
2. Unscrew and remove the spool housing by turning the
spool
clockwise.
22
NoTE: Do not try to remove the spool housing by
turning the spool cap
3. Remove spindle plate before installing a new housing.
Remove any dirt and grass from the motor housing and
spindle plate.
4. Install spindle plate onto the spindle
D shaped retaining nut
base of the spindle plate.
5. Align the spindle plate hole and notch, insert a
screwdriver back into the hole and thread the new spool
housing counterclockwise. Securely tighten the new
spool housing onto the spindle.
MAINTENANCE (Fig. T)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories, when
replacing line, or prior to cleaning. An accidental
start-up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
1. Keep the air intake slots
(Fig. T).
2. Your trimmer line can dry out over time. To keep your
line in top condition, store spare line in a plastic, sealable
bag with a tablespoon of water.
3. Plastic parts may be cleaned by using a mild soap and a
damp rag.
4. The line cutter on the edge of the guard can dull over
time. It is recommended you periodically touch-up the
sharpness of the blade with a file.
until the hole
in the
9
30
in the guard
32
will be visible as
4
9
until the hole
30
in the
32
in the guard.
.
38
, so the double
31
on the spindle sits inside the
37
clean to avoid overheating
35
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this procedure.
WARNING: Never use solvents or other harsh
. A
8
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those
34
offered by D
product, use of such accessories with this tool could
be hazardous. To reduce the risk of injury, only
D
WALT-recommended accessories should be used
e
with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
Repairs
The charger and battery pack are not serviceable.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement) should be performed by a
D
WALT factory service center or a D
e
service center. Always use identical replacement parts.
DCST925
WALT, have not been tested with this
e
SPECIFICATIONS
ENglish
WALT-authorized
e
20V Max*
31
Publicidad
