Publicidad
Idiomas disponibles
Idiomas disponibles
5. Before starting the equipment
Warning!
Always pull out the battery before making ad-
justments to the equipment.
All covers and safety devices must be properly
fi tted before the equipment is switched on.
5.1 Fitting the extraction socket
(Fig. 1.2+1.3/Item 20/26)
Caution! For health and safety reasons it is
imperative that you use a dust extractor.
•
Connect your cordless tool to a domestic
vacuum cleaner or a dust extractor using the
extraction socket (20/26). This will ensure
optimum dust extraction from the workpiece.
The benefits are that you will protect both the
equipment and your own health. Your work
area will also be cleaner and safer.
•
Dust created when working may be dange-
rous. Refer to the section entitled "Safety inst-
ructions".
•
The vacuum cleaner you use for the vacuum
extraction must be suitable for the material
you are machining. Use a special vacuum
cleaner if you are handling harmful materials.
Cordless router (Fig. 1.3/Item 20)
•
Use the retaining hook to attach the extractor
adapter (20) to the routing shoe (a) and secu-
re it with the fastening screw for the extractor
adapter (21).
•
The extractor adapter (20) can be connected
to extractor units (vacuum cleaners) with a
suction hose.
•
The internal diameter of the extractor adapter
is 36 mm. Now fit a suction hose of matching
size to the extractor adapter.
Cordless palm router (Fig. 1.2/Item 26)
•
Secure the extractor adapter (26) to the
palm router insert (36) using the countersunk
screw (27).
•
The extractor adapter can be connected to
extractor units (vacuum cleaners) with a suc-
tion hose.
•
The internal diameter of the extractor adapter
is 36 mm. Now fit a suction hose of matching
size to the extractor adapter.
Anl_TP-RO_18_Li_BL_EX_ZA_SPK7.indb 14
Anl_TP-RO_18_Li_BL_EX_ZA_SPK7.indb 14
GB
5.2 Fitting the safety guard
(Only for the cordless router!)
(Fig. 3/Item 15)
Fit the safety guard (15) as shown in Fig. 1.
To remove the safety guard (15), pull it to the
front.
5.3 Fitting the parallel stop (Fig. 4/ Item 34)
Cordless router
•
Insert the holder for the parallel stop (16) in
the guides provided on the routing shoe (a)
as shown in Fig. 1.1 and secure with the two
fastening screws for the holder for the parallel
stop (17).
•
Undo the fastening screw for the parallel stop
(18) on the holder for the parallel stop (16).
•
Insert the parallel stop (34) in the holder for
the parallel stop (16) as shown in Fig. 4.1 and
retighten the fastening screw for the parallel
stop (18).
•
Set the parallel stop (34) to the required di-
mension and secure it in place with the wing
screw (c).
Cordless palm router
•
Undo the fastening screw for the routing gui-
de (25).
•
Insert the parallel stop (34) in the holder for
the routing guide (25) as shown in Fig. 4.2
and retighten the fastening screw for the rou-
ting guide (25).
•
Set the parallel stop (34) to the required di-
mension and secure it in place with the wing
screw (c).
5.4 Fitting the compass point (Fig. 5/Item 33)
•
You can cut circular areas using the compass
point (33).
•
To do so, undo the wing nut (c) and remove
the front section of the parallel stop (34).
•
Screw-fit the compass point (33) on the par-
allel stop (34) as shown in Fig. 5. Now fit the
parallel stop (34) together with the compass
point (33) on the router.
•
The procedure for fitting is the same as de-
scribed in section 5.3 except that the parallel
stop (34) must be turned through 180° so that
the compass point (33) points downwards
(Fig. 5).
•
Set the required radius between the compass
point (33) and the cutter.
•
Position the compass point (33) in the center
of the circle you wish to cut.
- 14 -
26.01.2024 09:24:29
26.01.2024 09:24:29
Publicidad
