EINHELL TP-RO 18 Set Li BL Manual De Instrucciones Original página 16

screw (b) to secure the routing guide.
6. Operation
•
Never use a low-quality or damaged cutter.
Use only cutting tools with a shaft diameter of
¼ " or 8 mm. The cutters must also be desig-
ned for the respective idling speed.
•
Secure the workpiece so that it cannot be
thrown through the air as you work on it. Use
clamps or a vise.
•
Never cut over metal parts, screws, nails etc.
6.1 On/Off switch (Fig. 1/Item 3)
For safety reasons, the cordless router/palm
router is equipped with a safety lock-off .
•
To switch on, press the unlock/lock button (2).
The LED lamp (37) will begin to shine by way
of confirmation.
•
Now press the On/Off switch (3) within the
next 10 seconds.
•
If the On/Off switch is not pressed for longer
than 10 seconds, the LED lamp (37) will go
out and the equipment cannot be switched
on.
•
To switch off, press either the unlock/lock but-
ton (2) or the On/Off switch (3).
6.2 Speed control (Fig. 17/Item 4)
The most suitable speed depends on the material
you want to cut and on the diameter of the cut-
ter. Use the speed control switch (4) to select a
speed between 10,000 and 30,000 min
choose from 6 diff erent switch positions.
The speeds in the various switch positions
are as follows:
Switch position 1: approx. 10,000 min
speed)
Switch position 2: approx. 14,000 min
Switch position 3: approx. 19,000 min
Switch position 4: approx. 22,000 min
Switch position 5: approx. 25,000 min
Switch position 6: approx. 30,000 min
(maximum speed)
To increase the speed:
Move the speed controller (4) in the plus direction.
To decrease the speed:
Move the speed controller (4) in the minus direc-
tion.
Anl_TP-RO_18_Li_BL_EX_ZA_SPK7.indb 16 Anl_TP-RO_18_Li_BL_EX_ZA_SPK7.indb 16
GB
6.3 Adjusting the routing depth
(Only for the cordless router!) (Fig. 17)
•
Place the machine on the workpiece.
•
Undo the lock nut (11) and the clamp lever
(19).
•
Slowly move the machine downwards and
press the depth adjuster (12) until the cutter
makes contact with the workpiece.
•
Tighten the clamp lever (19).
•
Set the precision adjustment device (8) ac-
cordingly to 0.
•
Set the end stop (13) so that the depth stop
(14) lies above the lowest set end stop (13).
•
Press the depth adjuster (12) to lower the
depth stop (14) until it touches the end stop
(13). Then tighten the lock nut (11) and re-
lease the clamp lever (19).
•
Set the pointer (10) to the zero point on the
scale (9).
•
Undo the lock nut (11). Push up the depth
stop (14) until the pointer (10) shows the re-
quired routing depth on the scale (9). Retigh-
ten the lock nut (11).
•
Test the setting by performing a test cut on a
piece of scrap material.
•
Now the routing depth can be finely adjusted.
Begin by turning the precision adjustment
device (8) to the required dimension.
Turn the precise adjustment device (8) counter-
clockwise:
The routing depth is raised
Turn the precision adjustment device (8) clock-
. You can
-1
wise:
The routing depth is lowered
Turning the precision adjustment device (8) by
one increment is equivalent to changing the rou-
(minimum
-1
ting depth by 0.1mm; one full turn is equivalent to
1mm.
-1
-1
6.4 Routing
-1
-1
Cordless router
-1
•
To avoid damage to the router, make sure
there are no foreign objects attached to the
workpiece.
•
Hold both of the router's handles (7).
•
Place the cordless router on the workpiece.
•
Set the routing depth as explained in section
6.3.
•
Select the speed as explained in section 6.2
and switch on the equipment (see section
6.1)
- 16 -
26.01.2024 09:24:29 26.01.2024 09:24:29