DeWalt DCF620 Traducido De Las Instrucciones Originales página 20

EngLIsh
Changing Bit Holders (Fig. C)
1. Rotate the locking collar
from gear case.
2. Pull nose cone 4 off of gear case.
3. To remove:
a. Grab the bit holder 22 .
b. Push it into the gear case depressing the sleeve
c. Rotate the bit holder until the clutch engages.
d. While holding the sleeve depressed, pull the bit holder out.
4. Push and rotate the new bit holder into gear case, depressing
the sleeve, until ball lock snaps in groove in bit holder shank.
5. Replace nose cone 4 by placing on gear case and rotating
collar 1/4 turn to align arrow on gear case with the lock symbol
on collar.
Changing Bit Tip (Fig. C)
1. Rotate the locking collar
from gear case.
2. Pull forward on nose cone
clutch housing.
3. Use pliers to remove worn bit and install new bit tip.
Depth Adjustment
Follow the graphic on the collar to increase or decrease the
fastening depth. To seat the screw deeper in the workpiece, turn
the adjustment collar to the right. To seat the screw higher in
the workpiece, turn the adjustment collar to the left.
Prior to Operation
1. Make sure your battery pack is (fully) charged.
2. Insert the appropriate drive accessory.
3. Select forward or reverse rotation.
4. Set the appropriate driving depth.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Proper Hand Position (Fig. D)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the rear grip. Take
care to not block the air vents
Switching On and Off (Fig. A)
1. To run the tool, press the variable speed trigger switch
The pressure exerted on the variable speed switch determines
the tool speed.
2. To stop the tool, release the variable speed trigger switch
Lock-on Button
To lock the trigger switch 7
operation, depress the trigger switch and push up the
lock-on button 9 . The tool will continue to run. To turn the
tool off, from a locked-on condition, squeeze and release
20
1/4 turn to unlock nose cone
3
21
3 1/4 turn to unlock nose cone
and remove it from
4
.
23
in the ON position for continuous
the trigger once. You will hear and see the lock-on switch
return downwards.

CAUTION: Before using the tool (each time) be sure that the
locking button release mechanism is working freely. Be sure to
release the locking mechanism before disconnecting the battery.
Failure to do so will cause the tool to start immediately the next
time the battery is inserted. Damage or injury could result.
.
Screwdriving (Fig. A, D)
For best results, hold the screwdriver with your hand directly in
line with the fastener and press the variable speed switch with
the last one or two fingers of the hand. This reduces the chance
of the screw slipping from the drive accessory when pressure
is applied.
To drive the fastener, place it on the bit, press the variable speed
switch and push the fastener into the workpiece with a smooth,
continuous motion. When the fastener is seated, the clutch will
disengage automatically.
1. Install bit tip in bit holder.
2. Adjust depth locator
3. Check for correct rotation, start screwdriver and place screw
on bit.
4. Contact work surface, applying forward pressure to drive
screw until depth locator contacts the work surface. Screwgun
will ratchet automatically, disengaging bit from screw.
5. This depth sensitive screwdriver is suitable for driving
drywall screws.
For This Depth Sensitive Clutch Please Remember
• The bit will not turn until pressure is applied to the unit. Push
to engage.
• Trigger switch will not depress unless tool is in either forward
or reverse position.
Screwdriving with Collated Screws (Fig. E)
To drive collated screws the DCF6201/DCF6202 attachment
should be used. The magazine attachment allows for faster work
flow when driving multiple screws. Instruction for installation,
usage and cleaning of this attachment is included in the
attachment's supplied manual.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
.
7
Cleaning

WARNING: Blow dirt and dust out of the main housing with
7 .
dry air as often as dirt is seen collecting in and around the air
vents. Wear approved eye protection and approved dust mask
when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals may
weaken the materials used in these parts. Use a cloth dampened
.
1