DJ-Tech X10 Manual De Instrucciones página 7

1. Gain – Used to adjust the input level for each channel.
2. Booth Level – Adjusts the BOOTH output level.
3. Mic Level – Adjusts Microphone level.
4. MIC EQ – These controls are used to adjust the
microphone tone level HI and Low.
5. MIC OFF/ON/Talkover – To set mic on and off. When
switch at the talkover position, the mic is on, and the
sound level for everything other than that from the mic
will decrease around 20dB.
6. CUE Button – Used to select the channel(s) to be
monitored.
7. CH1/2, MASTER Switch – This switch will determine
the level meter mode.
In the "Master" position, the meter will show the output
level of the left and right channels. In the "CH1/2"
position, the left side of the meter will indicate monaural
level of CH1 and the right side of the meter will indicate
monaural level of CH2.
8. Channel Fader – Adjust the volume for CH1 and CH2.
9. Cross Fader – Used to mix the sound from the 2
channels.
10. Level Meter – Show the level depending on the position
of the CH1/2, MASTER Switch in No. 7,
11. Split Cue Button
i) In the STEREO mode, the stereo sound of MASTER
and CUE are fed to both ear cups. In the SPLIT CUE
mode, the headphone circuit provides monaural CUE
sound to the left and monaural MASTER sound to the
right.
ii) When the Level Meter mode select switch is set to
"MASTER". In the STEREO mode, the meter indicates
the stereo level in the L/R Master output. In the SPLIT
CUE mode, the monaural CUE sound level is displayed
on the left and the monaural MASTER sound level is
displayed on the right.
iii) In the SPRIT CUE mode, the LED of the switch is lit.
12. Headphones Level – Adjust the Headphones output
level.
13. CUE Pan
i) This function allows you to monitor the CUE level as
well as the MASTER output in your headphone s. A CUE
Level may only be monitored of the CUE signal is
selected.
ii) Serves two purposes. In the STEREO mode it
changes the relative levels of the CUE and MASTER
mixed together in both ear cups. In the SPLIT CUE
mode it changes the balance between the monaural
CUE sound in the left and monaural MASTER sound in
the right.
14. Input Select Switch – These switches are used to
select the input source assigned to each channel. Each
channel may only be assigned one input source at a
time.
15. Master Balance Control – This knob is used to control
the pan, adjust how much of the signal is sent to the L
and R output level.
16. Master Level – Adjusts the Master output level.
17. Power Switch – Turns this unit power ON/OFF.
18. Power Connector – Plug in power adaptor here.
Please use only the included DC adaptor or a 6V
adaptor with the same rating.
19. Master Balance Output – These 1/4" TRS jacks
provide a balanced line level output.
20. Master Unbalance Output – Left and Right line level
unbalanced RCA.
21. Booth Output Jacks – Connect to inputs of your active
monitors using RCA cables.
22. CD Input Connectors – Use to connect a DJ CD player
or other component with line level output.
23. PH/LN Jacks – These jacks are inputs for a phono
(RIAA) stage for magnetic (MM) cartridge or a line level
device.
24. PH/LN Switch – These switches are used to change
the mode of Phono input jacks. When connecting
turntable to these jacks, be sure the switch is in the
Phono position. When using Line level input devices,
select LN. Always be sure main power is shut off before
change the position of the PH/LN selector switch.
25. GND Terminals – Connect each of your turntable
ground leads to these two ground terminals.
26. Fader Start Control Jacks – Connect these jacks to
the fader input jacks of the CD player using a 3.5mm
mini-jack cable.
27. USB1/2 Port – 2 extra USB ports from the internal USB
Hub. Used to connector to other USB devices like USB
DJ controller.
28. USB Port – Use the included USB cable to connect to
your computer.
29. Fader Start Switch – Use this to switch the Channel
Fader Start function ON and OFF.
30. MIC Connector – This jack is used to connect a
microphone to the mixer. Connect you microphone via
this combo jack (XLR or 1/4 inch).
31. CrossFader Switch – Use th is to switch the Crossfader
Start function ON and OFF.
32. CrossFader or Channel Fader Contour Adjustment –
Adjusts the shape of the crossfader curve from a fast cut
for scratching or to a slow fade for mixing.
33. CrossFader or Channel Fader Reverse Switch –
Reverses the direction that the Crossfader or Channel
Fader.
34. Phones Output – Connect your headphones to this
3.5/ 6.3mm jack.
7