Publicidad
Idiomas disponibles
Idiomas disponibles
22
SEARCH KNOB:
Press this button to toggle
between fast search (LED lit) and slow search (LED
off). The fast search will automatically turn off if the
jog Wheel is not used for more then 10 Seconds. When
in PLAY mode, you can use the jog Wheel to search
fast, backward or forward through the current track. If
in PLAY mode and the SEARCH mode is not activated
the JOG WHEEL will act as a PITCH BEND.
When in PAUSE mode, you can use the jog Wheel to
search, backward or forward through the current
track. If the SEARCH button is activated you can
search fast through the track, if the button is not
activated you can search frame by frame or a slow
search.
23
If a SEAMLESS LOOP has
RELOOP BUTTON:
been made, but the Player is not actively in
SEAMLESS LOOP mode (a loop is not playing),
pressing the RELOOP BUTTON will instantly
reactivate the SEAMLESS LOOP mode. To exit loop,
press the B/EXT BUTTON. LOOP and RELOOP will
appear in the LCD DISPLAY when the RELOOP
function is available.
24
GAIN INPUT FADER (Channel Fader):
faders are used to control the output signal of any
source assignedto its particular player (only available
when MIXER OUTPUT is ON).
25
CHANNEL GAIN CONTROL:
used to adjust the audio source signal input gain for a
channel. Never use the gain control to adjust a channels
output volume. Setting the gain level properly will
ensure a clean output signal. An improper gain level
adjustment will send a distorted signal throughout the
entire audio line, which may damage speakers and
amplifiers. (only available when MIXER OUTPUT is
ON)
26
These are the SD slots where
SD CARD SLOTS:
you insert your SD cards. One card per slot. It cannot
read a SD Card higher then 4GB. It cannot read or
accept a SDHC Card; it must be a regular SD Card. The
preferred file format is MP3.
27
PITCH SLIDER:
This slider is used to adjust the
playback pitch percentage. The slider is a set
adjustment and will remain set until the pitch slider is
move or the pitch function has been turned off. This
adjustment can be made with or without a SD card in
the player. The pitch adjustment will remain even if a
SD card has been remove and will reflect on any other
SD card inserted into the player. That is to say, if you set
a +2% pitch on one SD card, remove that card and
insert another, that SD card too will have a +2% pitch.
The amount of pitch being applied will be displayed in
the LCD.
28
LCD DISPLAY:
This high quality LCD display
indicates all the functions, as they are occurring. This
display is viewable at several comfortable angles.
REAR PANEL
1
1
AUDIO OUTPUTS:
the audio signal from player 2. Use the supplied cinch/cinch cables to
connect these outputs to the CD/line input of an external mixing unit.
2
FADER START sockets:
be linked for relay play. This can also be connected to a mixing board
that supports automatic fader start.
3
POWER CONNECTOR:
switching adapter to suitable to each voltage.
4
AUDIO OUTPUT from player 1 or mixer:
the setting of the MIXER OUTPUT MODE.
DISPLAY LCD
17
1
2
16
These
This knob is
15
14
1
CUE INDICATOR:
CUE mode and will flash every time a new CUE POINT is set.
2
FOLDER INDICATOR:
playing folder.
3
TIME BAR INDICATOR:
depending on the setting of the SETUP MODE (see chapter
-
SETTING SETUP MODE
flash shortly before the end of a track. The flashing bar is a great visual
reminder a track is about to end regardless of which time mode the unit is.
4
BPM STATUS:
active.
5
BPM METER:
Indicates the BPM value of the currently playing track.
6
PITCH METER:
7
Indicates if the tempo lock is activated (lock symbol).
TEMPO LOCK:
8
LOOP INDICATOR:
9
RELOOP INDICATOR:
activated with the Reloop function.
10
AUTO CUE STATUS:
11
TIME DISPLAY:
minutes, seconds and frames.
12
ALPHANUMERIC DISPLAY:
track, of the folder and the sampling rate. For VBR recorded MP3 tracks
3
2
4
2
AUDIO OUTPUT from player2: Output for
This connection allows two players to
:
Plug in power adapter here. It is a
Output depending on
3
4
6
5
13
12
11
8
10
This indicator will glow when the device is in
Indicates the number of the currently
Shows either time remaining or elapsed
SYSTEM
for more information) This bar will begin to
This will indicate that the AUTO BPM counter is
Indicates the percentage of a track's pitch.
Indicates if LOOP function is activated.
Indicates if a loop has been set which can be
Indicates ifAuto Cue is activated.
Indicates the time of the chosen Time mode in
Indicates the current name of the
the display only show "VBR". All kinds of other interactive
information is also shown.
13
Indicates the elapsed time of a track
TIME MODE:
("ELAPSED") or the remaining time of a track ("Remain"). (see
chapter
SYSTEM SETTING
information)
14
REPEAT INDICATOR :
REPEATED play mode.
15
Indicates whether the play mode is
SINGLE INDICATOR:
set to single ("SINGLE") or continuous mode (no display).
16
TRACK INDICATOR:
currently playing track.
17
PLAY/PAUSE INDICATOR:
mode ("
►
►
"), or the player is in pause mode (" ").
FUNCIONAMIENTO
CARD SELECT functions
1
LED DISPLAY TO CARD SELECTING:
7
power and the relational LED goes out. Whether you have inserted
SD card or not, the default for SD card selection is as below: SD B
LED is on in the player 2.
SDALED is on in the player 1
SD B LED is on in the player 2.
2
There is a CARD SELECT BUTTON to
CARD SELECT:
9
select the card playback in each PLAYER by your desires. You
have two different choices as below:
(a) THE SAME CARD PLAYBACK To play the same
card in both player 1 and player 2; insert the card into
either SDA or SD B slot. Press the CARD SELECT and
both SD A LEDs in the player panel are on when card is in
SDAslot; either does when card is in SD B slot.
(b) TWO CARDS PLAYBACK Each SD slot inserts a
card to play. And each player select different SD slot to
play.
Case 1:
Case 2:
－
for more
SETUP MODE
Indicates whether the unit is in
Indicates the number of the
Indicates the device is in play
׀ ׀
׀ ׀
Switch on the
Publicidad
