Wolf Garten Robo Scooter 500 Instrucciones De Servicio Originales página 39

Weekly Program
3
Note
The 'Weekly program' menu allows you to set an automatic
weekly program by the size of the area connected to the Base
Station.
z By setting the area of the zone connected to the Base Sta-
tion, Robo Scooter 500 will automatically determine the
most suitable weekly program to your lawn.
z Robo Scooter 500 will start mowing at 13:00 on the active
days and will drive back for charging in the Base Station at
the end of the operation.
1
Warning!
Never let Robo Scooter 500 operate without supervision. Seri-
ous injury can occur. If the current date and time are not set
correctly or are failed to be set when prompted, the times sche-
duled for automatic departure will not be correct. Incorrect de-
parture times can be dangerous if children, pets or bystanders
are present in the mowing area.
1. Press 'GO'
2. Press 'GO'to set an automatic weekly
program by area or scroll to change it
to 'Off'.
3
Choose 'Off'if you do not want to
use automatic scheduled opera-
tions.
3. Press 'GO'
4. Scroll 'UP'to choose the lawn area
connected to the Base Station
5. Press 'GO'
6. Follow the instructions at the next
subparagraph ('Base position'tes-
ting)
Testing the Base Station and Perimeter Wire Position
1
Attention!
It is required to test the position of the Base Station and the Pe-
rimeter Wire to determine if any small adjustments need to be
made.
1. Position the Robo Scooter 500 inside the lawn towards the peri-
meter wire, at least 2 meters from the Base Station.
2. Press 'GO'to testthe Base Station
position.
3
Note
In a case you forgot to connect the Power Supply to a regular
household receptacle 230 Volts (120V), 'No wire signal' mes-
sage will be displayed on the LCD upon pressing GO.
z Reminding you to connect the Power Supply.
en
3
3. Follow the Robo Scooter 500 and
3
Weekly program
Press GO
Program On
Confirm
4. Fasten the base in place using the 2
Base zone area
Presse GO
150 - 200 m²
Confirm
200 - 250 m²
Confirm
5. Press 'GO'to test wire position.
Base position
6. Walk along the side of the Robo
Press GO to test
3
Base position
Press GO to test
Completing the Wire Fastening
z Once complete, walk back along the perimeter and add in wire
Note
In a case you connected the Perimeter Wire in the opposite di-
rection, 'Change wires in plot connector' message will be dis-
played upon pressing GO.
z Instructing you to switch between the two wires connected
to the Plot connector.
confirm that it docks properly into the
Base Station.
Note
If Robo Scooter 500 fails to enter
the Base Station, it will stop.
Reposition Base
Press GO
z Slightly move the Base Station,
so that Robo Scooter 500 en-
ters the Base Station as cente-
red as possible;Reposition
Robomow and press 'GO'for
retesting.
stakes and press 'GO'.
Scooter 500 while it is following the
edgeuntil completing one lope of the
perimeter without striking any ob-
ject(it will stay in the Base Station).
Note
Robo Scooter 500 collides with
obstacle, drives back and stops.
Adjust wire
then press GO
z Adjust the wire and press
'GO'to continue testing the wire
position.
pegs to those areas of the wire where it is not pulled down below
the level of the grass tips and close to ground level. Wherever the
wire is raised or loose, it should be tightened and pegged down
with extra wire pegs (distance between pegs should be 0.5 to 1
meter (1.5-3 ft) in straight line and more when curved).
Searching base
Peg base
then press GO
Wire position
Press GO to test
Wire position
39