Safety Information; Technical Data - Oregon 310-230 Manual De Instrucciones

310-230
EN
WARNING: READ AND UNDERSTAND ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.
FAILURE TO FOLLOW THE WARNINGS AND INSTRUCTIONS MAY RESULT IN ELECTRIC SHOCK,
FIRE AND/OR SERIOUS INJURY.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
This instruction manual contains translations of a manual drafted in English and are
provided to assist those who do not speak English as their first language. Being a
technical writing, some terms may not have a like or equivalent meaning as translated.
Therefore, you should not rely on this translation, and should cross-reference the English
version, where relying on the translated instructions could result in harm to your person
or property.

Safety Information

WARNING The use of accessories or attachments not recommended
by the manufacturer may result in a risk of injury to operator or
bystander . Any maintenance operation not described in this manual
must only be carried out by an AUTHORISED service centre .
WARNING Replace cracked or damaged grinding wheel immediately .
Serious injury to operator or bystander could result from a damaged wheel .
- Use a grinding wheel suitable for the type of chain to be sharpened;
consult the chain chart at the end of the manual .
- Do not force the grinding wheel on the hub and do not alter the centering
hole diameter . Do not use grinding wheels that do not fit perfectly in place .
- Use clean and perfectly intact hub and flange to fit the grinding wheel .
- Make sure the outside diameters of the hub and flange are identical .
CAUTION The following instructions should be carefully followed in order
to reduce the risk of kickback resulting from improperly sharpened saw chain .
ATTENTION When you use electrical appliances, you
should always observe basic safety precautions to reduce
the risk of fire, electric shocks and personal injuries .
Do not leave the machine out in the rain .
Do not use the machine in damp or wet places .
Keep the work area well lit .
Do not use the machine near flammable liquids or gas .
Make sure the voltage and the frequency written on the
rating nameplate match those of the mains .
Make sure the switch is turned off (position "0") before you plug the
machine into the mains to prevent it from starting up accidentally .
Unplug the machine from the mains when it is not in use, before you start any
maintenance jobs and when you replace any accessories (i .e . grinding wheel) .
Before use, ensure the machine is able to work properly:
check the integrity of the shield guard in particular .
Check the alignment and adherence of moving parts, make sure nothing is broken,
check the overall assembly and any other conditions that may affect operation .
The grinding wheel safety guards and any other parts damaged shall be repaired
or replaced by a skilled technician, unless specified otherwise in this manual .
Have faulty switches replaced by a skilled technician .
Keep anyone that is not involved in the job well away from the work area,
especially children . Do not let them touch the machine or the extension lead .
Wear safety goggles and gloves .
Wear a face mask or dust mask if the process creates dust .
Do not wear baggy clothing or jewelry, which could get caught up in moving parts .
Tie long hair back .
Wear non-slip shoes when working outdoors .
Always stand appropriately and balanced on both feet .
Always keep your eyes on the job, without distraction . Use your
common sense and do not use the machine if you are tired .
Keep the work area clean and tidy . Untidy work areas
and benches could cause accidents .
Avoid contact with un-grounded connected surfaces .
Always use the vise to firmly hold the chain to be sharpened .
Never sharpen the chain while holding it with your hands .
Do not force the machine to work at a higher speed than recommended .
Never stop the grinding wheel with your hands, even
after the motor has been switched off .
When using the machine outdoors, use extension leads
approved for such use and marked accordingly .
Never pull on the power cable to unplug the machine from the
mains . Keep the cable away from heat, oil and sharp edges .
Do not use the machine if the switch does not switch on or off .
The use of accessories (i .e . grinding wheel) different from those
recommended by the manufacturer could cause injuries .
Do not tamper with the safety devices .
Look after the machine with care .
Follow the instructions when replacing accessories .
Occasionally visually check the machine cable and have it
repaired by a specialist if you should notice any damages .
Occasionally visually check the extension leads and replace them if damaged .
Keep the operating handles dry, clean and free from oil and grease .
When the machine is not in use, keep it in a dry and
safe place away from children's reach .
This electrical machine complies with related safety provisions . Repairs shall
be carried out exclusively by a skilled technician, using exclusively OEM spare
parts, otherwise whoever uses the machine could be in serious danger .
GENERAL INFORMATION
The manufacturer is not liable for damages in the following cases:
- failed observance of the instructions given herein;
- use of the machine other than that described in the "INTENDED USE" section;
- failed use in compliance with current standards on
Health and Safety at the workplace;
- Incorrect installation;
- lack of scheduled maintenance;
- modifications or jobs that are not authorized by the manufacturer;
- use of non-original or inadequate spare parts;
- repairs that are not carried out by a specialist .
USING AND KEEPING THE OWNER'S MANUAL
The characteristics and the information given in this manual are
merely indicative . The manufacturer reserves the right to add any
modifications to the grinder considered necessary at any time .
It is forbidden to reproduce any part of this document without
authorisation on behalf of the manufacturer .
The owner's manual is integral part of the machine and must be kept
in a safe place so that it can be consulted whenever need be .
If you should lose your manual or it should deteriorate, you can ask
your dealer or an authorized service centre for another copy .
The manual shall accompany the machine at all times,
especially if it is sold at a later date .
DEFINITIONS
Skilled technician: a person who is generally employed by the
service centre and who is trained to carry out extraordinary
maintenance jobs and repairs on the machine .
SYMBOLS
This symbol points out the possibility of serious personal injuries
if the provisions and instructions are not complied with .
This symbol points out that the user must wear
protection goggles when using the machine .
This symbol points out that the user must wear
protective gloves when using the machine .
Read the instructions before using the machine
This symbol (on the rating nameplate) points out that the product
must not be disposed of with normal household waste . Contact
an authorised shop or your dealer for disposal instructions .

TECHNICAL DATA

Model
Voltage
Rated power
Grinding wheel dimensions
Maximum speed of grinding wheel
Types of chains that can be sharpened 1/4" - .325" - 3/8" - .404"
Weight (complete machine)
SAFETY DEVICES
The grinder is equipped with the safety devices illustrated hereafter:
Shield guards: they protect the operator from parts of the grinding
wheel that may come away during the sharpening process .
310-230
230V~ 50Hz
85W
Outside Ø 105 mm - Inside Ø 22,2 mm
Thickness: 3 .2 - 4 .7 - 6 .0 mm
-1
5300 min
2,1 kg
EN
3