Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
VOX
(long press)
The VOX function allows
transmitting
phone (or in the optional vox microphone) without pressing the PTT switch
(13). The use of an optional vox microphone connected to the rear panel
disables
of the transceiver (E)
Press shortly VOX key (10) in order to
appears on the display. Press shortly again the VOX key (10) to
function. "VOX" disappears.
11) USB CHARGING SOCKET
The USB socket (16) can be used to charge smartphones, tablets or other
rechargeable devices with 5 V - 2.1 A.
12) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the
setting of the equipment into the dashboard easier.
See Cabling Diagram page 57.
13) PTT (Push To Talk)
Transmission key, press to
transmit
to
listen to
an incoming communication,
TOT (Time Out Timer)
If the PTT switch (13) key is pressed for more than 3 minutes, the display starts
blinking and the transmission ends. A beep will sound until the PTT switch
(13) key is released.
14) UP/DN BUTTONS ON MICROPHONE ~ SCAN
UP/DN BUTTONS ON MICROPHONE
Press UP/DN buttons (14) on the microphone to
increase
and DN to
decrease
See ROTARY CH KNOB page 33.
SCAN
(very long press)
Press and hold the UP or DN button (14) for ± 7 seconds or until a beep
sounds to activate the SCAN function. The dot between the two channel
digits flashes to indicate that the function is active.
The scanning stops as soon as there is a busy channel. The scanning au-
tomatically starts 3 seconds after the end of the transmission and no key
is activated during 3 s. In
SCANNING
by speaking into the original micro-
the original microphone.
activate
the VOX function. "VOX"
disable
a message,
is displayed and release
disappears.
(short press)
change
the channel. UP to
the channel.
mode, turn the F rotary knob (9) or
press the UP/DN buttons (14) on the microphone to change scan direction.
Press PTT switch (13) to exit SCAN. The dot between the two channel digits
disappears from LCD.
A) DC-POWER TERMINAL (13,2 V / 26,4 V)
B) ANTENNA CONNECTOR (SO-239)
C) JACK FOR EXTERNAL OPTIONAL SPEAKER (8 Ω, Ø 3.5 mm)
the
D) JACK FOR PA OPTIONAL SPEAKER (Public Address) (8 Ω,
Ø 3.5 mm)
E) JACK FOR OPTIONAL VOX MICROPHONE (8 Ω,Ø 2.5 mm)
C) FUNCTION TURNING ON THE UNIT
To
select
the FREQUENCY BAND turn off the unit. Press and hold the F key
(9) and then turn the unit on.
(Configuration: EU; PL; d; EC; U; In)
The frequency bands have to be chosen according to the country of use.
Don't use any other configuration. Some countries need a user's licence.
See table page 59.
1.
Turn on the power while pressing the F key (9). The letter corresponding to
the current configuration is blinking.
2.
In order to change the configuration, use the rotary CH knob (3) on the unit
or the UP/DN buttons (14) on the microphone.
3.
When the configuration is selected, press the F key (9) during 1 second. The
letter corresponding to the configuration is continuously displayed and a
confirmation beep sounds.
4.
At this point, confirm the selection by switching off the transceiver and then
switching it on again.
See the frequency bands table at pages 54 to 56 / configuration table
page 58.
D) MENU
The order of 11 functions is as described in this manual. However, the func-
tion displayed by entering the MENU will be the last function modified by
user.
The procedure is the same Whatever the function is:
Press F knob (9) to
enter
1.
Turn the rotary CH knob (3) or use UP/DN buttons (14) on the microphone
to
select
the menu.
35
MENU.
is displayed.
Publicidad
Tabla de contenido
