Alarms Management - Parker Hiross Hyperchill ICE007 Manual De Uso

English
General
Th ere are two levels of protection for parameters:
a) Direct (D): with immediate access, User-changeable;
b) Password protected (U): password required for access; Factory-set
parameters.
4.4.1 Sensor parameters
PARAMETER CODE
/23
Unit of measurement
4.4.2 Regulator parameters
PARAMETER CODE
r01
Summer set point.
r02
Summer diff erential.
4.4.3 Anti-frost/B2 backup heating element parameters
PARAMETER CODE
A01
B2 anti-frost alarm set point.
A02
Anti-frost alarm diff erential.
B2 cooling anti-frost heating
A04
element set point.
B2 cooling backup heating ele-
A05
ment diff erential.
Automatic anti-frost switch-on
A10
(section 4.4.3.1).
4.4.3.1 Automatic anti-frost switch-on
0
Disabled.
1
Heating element and pump on simultaneously at
2
Heating element and pump on independently at
3
Heating element and pump on at A04
4.4.4 Visualization sensor parameters B1/B2
PARAMETER CODE
Visualization sensor B1
b01
(water out)
Visualization sensor B2
b02
(evaporator)
4.4.5 Alarm parameters
PARAMETER
Level alarm delay aft er pump start.
Normal operating level alarm
delay.
Low pressure alarm delay aft er
TYPE DEFAULT
compressor switch-on.
0
U
B1 high temperature alarm set
point.
TYPE DEFAULT
B1 low temperature alarm set
12.0
point.
D
3.0
4.4.6 Compressor parameters
D
PARAMETER
Minimum `On' time.
TYPE DEFAULT
3.0
Minimum `Off ' time.
D
5.0
Time between two compressor
D
switch-ons.
5.0
D
Switch-on delay.
Compressor switch-on delay aft er
1.0
D
pump start.
Pump switch-off delay.
0
U
Compressor hour counter.
Functioning hour counter
threshold.
Pump hour counter.
A04 .
Minimum time between two
A04 .
pump switch-ons.
.
Minimum pump on time.
4.4.7 General parameters
TYPE DEFAULT
PARAMETER
D
Enable digital input on/off .
Enable keypad.
D
Serial address.
4.5 Parameter management
4.5.1 Temperature setting (see fi g.1)
1. Turn the main swicth (QS) to "ON" and wait for the temperature
visualization.
2. Press and hold button "P2" (SEL) for more than 5 seconds to access
ICE007-010
CODE TYPE DEFAULT
P01 5
U
P02 5
U
P03 120
U
P16 80.0
U
P19 -40.0
U
CODE TYPE DEFAULT
c01 0
U
c02 0
U
c03 360
U
c06 0
U
c07 5
U
c08 0
U
c10 0
D
c14 0
U
c15 0
D
c17 0
U
c18 0
U
CODE TYPE DEFAULT
H07 1
U
H09 1
U
H10 1
U
the menu "D".
3. Select the parameter "-r-" using the "P3" and "P4" buttons, then
press button "P2" (SEL) to enter.
4. Select the parameter "r01" using the "P3" and "P4" buttons, then
press button "P2" (SEL) to enter.
5. Change the value, using the up and down arrow buttons "P3" and
"P4", then press button "P2" (SEL) to exit and save.
6. Press button "P1" (PRG) to exit.
4.5.2 Diff erential setting (see fi g.1)
1. Turn the main swicth (QS) to "ON" and wait for the temperature
visualization.
2. Press and hold button "P2" (SEL) for more than 5 seconds to access
the menu "D".
3. Select the parameter "-r-" using the "P3" and "P4" buttons, then
press button "P2" (SEL) to enter.
4. Select the parameter "r02" using the "P3" and "P4" buttons, then
press button "P2" (SEL) to enter.
5. Change the value, using the up and down arrow buttons "P3" and
"P4", then press button "P2" (SEL) to exit and save.
6. Press button "P1" (PRG) to exit.
4.5.3 Visualization sensor B1,B2
1. Press and hold button "P2" (SEL) for more than 5 seconds to access
the menu "D".
2. Select the parameter "-b-" using the "P3" and "P4" buttons, then
press button "P2" (SEL) to enter.
3. Select the parameter "b01" or "b02" using the "P3" and "P4"
buttons, then press button "P2" (SEL) to see the temperature.
4. Press button "P1" (PRG) to exit.
4.6

Alarms management

4.6.1 Digital input alarms
ID CODE DESCRIPTION
tP
ID1 Pump thermal cutout alarm. / Phases
monitor
FL
ID2 Water tank low water level alarm / No
water fl ow.
HP1
ID3 High pressure alarm from pressure
switch.
LP1
ID4 Low pressure alarm from pressure
switch.
4/6
RESET
M
A
M
M