Audio Controls; Volume Controls And; Listening Selector Buttons; Recording Selector Buttons - Rotel RC-1090 Manual De Instrucciones

RC-1090 Stereo Control Amplifier

Audio Controls

Volume Controls
The front panel Volume control
or decreases the volume in both channels at
the same time. Turn it clockwise to increase
the volume or counterclockwise to decrease
the volume. On the RR-969 remote Volume
Button , press the to increase volume
or to decrease volume.

Listening Selector Buttons

and Display
Press one of the Listening Selector Buttons
to select the input signals that goes to the
main outputs and to the power amplifier –
or, more simply, which source is heard. The
source selected is shown in the front panel
FL Display .

Recording Selector Buttons

and Display
Press one of the Recording Selector Buttons
to select the input signal that goes to the record
outputs. The source selected is shown in the front
panel FL Display . When you are not re-
cording, press the Off button. This minimizes
the chance of interference from other compo-
nents in the system.
Having a separate Recording and Listening
selector adds a significant degree of flexibil-
ity in how you can use the RC-1090. For ex-
ample by selecting CD with the Record Se-
lector and selecting Tuner with the Listening
Selector you can record a CD onto a tape while
listening to the tuner.
If you wish to duplicate ("dub") a recording
from one recorder to another, the source unit
must be connected to Tape 1 in/outputs. Press
the Tape 1 Recording Selector button. Con-
nect the unit recording the signal to the Tape
2 in/outputs.

Phones Output

The Phones output allows you to connect head-
phones for private listening. This output ac-
commodates standard stereo phone (
plugs. If your headphones have another type
1
of plug, such as a / " mini-plug, you will
8
need an adapter plug. Contact your autho-
rized Rotel dealer, to get the correct adapter
plug. Note: Plugging in a set of headphones
and
does not cut off the signal to the outputs. The
power amplifier will continue to receive a signal
increases
and the speakers will continue to play.

Remote Sensor

The Remote Sensor is located to the right of
the Phones jack on the front panel. It picks
up the infra-red signals from the remote control.
Do not cover or block the sensor. It must be
clear of obstructions or the remote control will
not work properly. The operation of the Re-
mote Sensor can also be affected if it is ex-
posed to bright light, particularly sun light.
In addition remote control functions may not
work reliably if the batteries in the RR-969
are weak.

Remote Control Functions

Selecting Listening Input

To select listening sources press:
Source
Phono
CD
Tuner
DVD/Video
Aux 1
Aux 2
Tape 1
Tape 2

Selecting Recording Input

To select the Recording Input press the Zone
button
you want. Refer to the table in the previous
paragraph. (Tape 2 cannot be selected as a
Recording Input.)
After you have selected a Recording Input the
Source Selection buttons revert to the Listen-
ing Input selection function. To turn the Re-
cording Selection off, press the Zone button,
then press the Shift button
1 / ")
4
Button
PH
CD
TUN
V1
V4
V5
TAPE 1
TAPE 2
, then press the button for the source
.
10

Mute Button

Press the Mute button to temporarily reduce
the volume of the system. Press the button again
to return the volume to its original level.

FL Display Control

Turning FL Display On/Off

To turn the front panel FL Display on or off,
press the Display
When the display is set to off, the Listening
Selector Display and Recording Selector Dis-
play will light for 5 seconds when a new source
is selected.

Customizing FL Display

You can program the RC-1090 to display
custom names, up to 5 characters long, in the
Listening and Recording Selection Displays.
For example, if the Aux 1 input was connected
to a Digital Satelite Dish, you could program
it to RC-1090 to display "DSS" when the Aux
1 input is selected.
Example:
1 Select Aux 1 as the listening input so AUX
1 appears in the display. Press and hold
the Menu/OSD
acters in the display change to blinking solid
blocks.
2 Use the RR-969
through the character set. (See page 3 of
the RR-969 manual for a listing of the char-
acter set.) When the character you want
is displayed, press Enter
and go to the next character.
3 Repeat the previous step to select the re-
maining characters. After the last charac-
ter is selected and confirmed the new name
is saved automatically.
Once the Listening input display is custom-
ized, the new name also appears when that
input is selected as the Recording input. (The
exception is the Tape 2 input since it cannot
be selected as the recording source.)
When an input that has a customized name
is selected, the original input name is displayed
for 2 seconds, before the customized name
is displayed.
button on the RR-969.
button until the char-
/ buttons to scroll
to confirm it