Setting Into Operation; Basic Adjustments; Operation Without Dmx Controller; Selecting A Function - IMG STAGELINE PARL-4SET Manual De Instrucciones

the set with the spigot into the reducing adapter and
GB
screw it down.
IMPORTANT! The stand must be set up in a stable
way. Check all locking screws for a tight fit and
tighten them, if necessary.
2. For fixing to a cross bar use two C hooks with M10
screw (e. g. TA-50* or TA-55*). In each case, put the
head of an M10 screw into the upper profile rail of
the control module and, together with the C hooks,
screw them down at the extreme ends of the profile
rail, if possible. Suspend the C hooks in the cross
bar and secure them with the locking screws.
3. If required, the spotlights may be rearranged in
the upper profile rail. For this purpose unscrew
the two lateral covers (1). Release the plug-in con-
nections (19) of the spotlights. First release the fix-
ing nut (18) and then the fixing nut (16) so that the
spotlights can be pushed out of the rail.
Then place the spotlights into the upper rail,
screw on again the lateral parts (1), tighten all nuts,
and reestablish the connections (19) to the control
module.

5 Setting into Operation

WARNING Never look directly into the LEDs; this
may cause eye damage.
Please note that fast changes in light-
ing, e. g. flashing light, may trigger
epileptic seizures with photosensitive
persons or persons with epilepsy!
Connect the mains cable provided to the mains jack (2)
first, then connect it to a socket (230 V~/ 50 Hz). While
starting, the display (10) shortly shows
unit will be ready for operation and can be controlled
via a DMX light controller (
matically operate according to the show programme
adjusted ( chapter 6). To switch off the unit, discon-
nect the mains plug.
Caution: Do not connect the unit to the mains voltage
via a dimmer!
For a more convenient operation, it is recommended to
connect the unit to a mains socket which is switched
on and off via a light switch.

5.1 Basic adjustments

The following basic adjustments can be made via the
display (10) and the control buttons (13). For this pur-
pose, press button MENU so many times until the
desired function is displayed. Then press button
ENTER. Make sure that the next button is pressed
within 1 minute, otherwise the adjusting process will
end. The menu structure can be found on page 19.
14
. Then the
chapter 7) or will auto-
*from "img Stage Line"
Blackout mode on or off
Use button DOWN or UP to select:
The spotlights will only light up when there is a
DMX control signal at the jack DMX INPUT (4).
Once the DMX controller is switched off, all
LEDs will go out.
This adjustment must be selected for the oper-
ation without DMX controller.
To memorize, press button ENTER.
Display on or off
Use button DOWN or UP to select:
The display (10) will always be on.
The display will be switched off approx. 60 s
after pressing the last button. It will be switched
on again the next time a button is pressed.
To memorize, press button ENTER.
Text on the display turned by 180°
Use button DOWN or UP to select:
normal representation
text turned by 180°
To memorize, press button ENTER.
One minute after pressing the last button, the adjusting
menu will be exited automatically. To exit immediately,
keep the button MENU pressed until the display shows
the function mode.

6 Operation without DMX Controller

When there is no DMX control signal at the jack DMX
INPUT (4), the yellow LED MASTER (8) will light up,
the display (10) will show the function adjusted and the
unit will automatically operate according to the show
programme selected. For this purpose, the Blackout
function must be deactivated,

6.1 Selecting a function

When selecting a function, make sure that the next
control button (13) is pressed within 60 seconds, oth-
erwise the adjusting process will end and the unit will
return to the previous function. The menu structure can
be found on page 19.

6.1.1 Show programmes

Two different colour change programmes (Nos. 1 – 2)
and ten different running light programmes (Nos. 3 – 12)
can be selected. In addition, there is a colour transition
programme (indication
No. 0. In programme No. 0 the unit will successively run
through the programmes 1 – 12 and
1) Press button MENU (13) so many times until
is displayed.
2) Activate the menu item with button ENTER. The
display (10) shows the adjusted show programme
( ... ,
chapter 5.1.
) and the programme
.
) in a flashing way.