Bypass Mode (Deactivated Sawstop Technology); Checking The Conductivity Of The Material; Triggered Sawstop Technology; Additional Settings/Functions - Festool TKS 80 EBS Manual De Instrucciones

English
► Press the red STOP button [2-2].
The SawStop technology is activated.
8.3 Bypass mode (deactivated SawStop
technology)
Only use bypass mode to saw conductive
materials. Activate the SawStop technolo­
gy again once finished.
Activating bypass mode
► Press and hold the yellow SawStop
switch [2-6].
The red LED [2-5] flashes once, and then im­
mediately
► press the green START button [2-3].
The TKS 80 EBS starts up.
The red LED [2-5] flashes again once.
► Release the yellow SawStop switch [2-6]
and the green START button [2-3].
The green LED [2-4] flashes slowly.
The red LED [2-5] is not lit.
The TKS 80 EBS is ready for use in bypass
mode.
Deactivating bypass mode (activating the
SawStop technology)
► Press the red STOP button [2-2].
The SawStop technology is activated.
8.4 Checking the conductivity of the
material
The conductivity of the material can be checked
in advance without triggering the SawStop tech­
nology.
► Press the green main switch [2-1].
The TKS 80 EBS is ready to use.
► Position the material against the saw blade.
The green LED [2-4] lights up constantly.
The red LED [2-5] flashes rapidly.
Material is conductive: Work in bypass mode
(see section 8.3 ).
The green LED [2-4] lights up constantly.
The red LED [2-5] is not lit.
Material is not conductive: Work with SawStop
technology active (see section
8.5

Triggered SawStop technology

Once the SawStop technology is triggered, the
saw blade comes to a stop under the table. The
cartridge [4-3] and the saw blade [4-1] must be
replaced.
34
8.2 ).
WARNING
Risk of injury due to uncontrolled start-up of
the bench-mounted circular saw
► Always disconnect the mains plug from the
socket before performing any work on the
machine.
Changing the cartridge and saw blade
► Remove the table insert (see section
► Remove the spacer wedge (see section
► Turn the cutting height setting [4-2] to the
minimum of 0 mm and turn it further
against the resistance.
Turn the cutting height setting [4-2] to the
maximum of 80 mm.
The cutting height is set to the maximum of
80 mm.
► Turn the cartridge locking device [4-4]
clockwise by one quarter of a rotation and
pull it out [4-5].
► Undo the spindle nut [4-6] and remove the
flange [4-7] of the saw blade.
► Use the spanner [4-8] as a lever to carefully
push the saw blade out of the tool spin­
dle [4-10].
Use the spanner [4-9] as a lever to carefully
push the cartridge out of the fastening
pins [4-11].
Repeat both steps until the saw blade and
the cartridge have been successfully re­
moved.
► Fit a new cartridge (see section
► Fit a new saw blade (see section
► Fit the table insert (see section
► Fit the spacer wedge (see section
9

Additional settings/functions

WARNING
Risk of injury, electric shock
► Always disconnect the mains plug from the
socket before performing any work on the
machine.
9.1 Electronics
The TKS 80 EBS is monitored electronically
with the following properties:
Smooth start-up
The electronically controlled smooth start-up
function ensures that the power tool starts up
smoothly. The limited starting current ensures
that even standard household fuses are not
triggered.
9.6 ).
9.8 ).
9.12 ).
9.11 ).
9.6 ).
9.8 ).