Electrical Requirements; Water Supply Requirements; Connect Water Supply - Sears Kenmore 106.5176 Serie Manual De Uso Y Cuidado

Electrical Requirements

WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it is important to
make sure you have the proper electrical connection.
Recommended Grounding Method
A 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded electrical supply
is required. It is recommended that a separate circuit serving only your
refrigerator be provided. Use an outlet that cannot be turned off by a
switch. Do not use an extension cord.
NOTE: Before performing any type of installation or cleaning, or removing
a light bulb, turn cooling off or turn the control (Thermostat, Refrigerator or
Freezer Control depending on the model) to OFF, and then disconnect the
refrigerator from the electrical source. When you are finished, reconnect
the refrigerator to the electrical source and turn cooling on or reset the
control (Thermostat, Refrigerator or Freezer Control depending on the
model) to the desired setting. See "Using the Controls" in the User
Instructions, User Guide, or Use & Care Guide.

Water Supply Requirements

Gather the required tools and parts before starting installation. Read and
follow the instructions provided with any tools listed here.
TOOLS NEEDED:
Flat-blade screwdriver
⁷⁄₁₆" and ¹⁄₂" open-end or
two adjustable wrenches
NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄" (6.35 mm)
saddle-type shutoff valve, a union, and copper tubing. Before purchasing,
make sure a saddle-type valve complies with your local plumbing codes.
Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve which reduces
water flow and clogs more easily.
IMPORTANT:
All installations must meet local plumbing code requirements.
Use copper tubing and check for leaks. Install copper tubing only in
areas where the household temperatures will remain above freezing.
Water Pressure
A cold water supply with water pressure of between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and ice
maker. If you have questions about your water pressure, call a licensed,
qualified plumber.
If your refrigerator has a water dispenser: After installation is
complete, use the water dispenser to check the water pressure.
10
¹⁄₄" nut driver
¹⁄₄" drill bit
Cordless drill
With the water filter removed, dispense 1 cup (237 mL) of water. If
1 cup of water is dispensed in 8 seconds or less, the water pressure
to the refrigerator meets the minimum requirement.
If it takes longer than 8 seconds to dispense 1 cup of water, the
water pressure to the refrigerator is lower than recommended. See
"Problem Solver" for suggestions.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a reverse
osmosis system going to the water inlet valve of the refrigerator needs to
be between 30 and 120 psi (207 and 827 kPa).
If a reverse osmosis water filtration system is connected to your cold water
supply, the water pressure to the reverse osmosis system needs to be a
minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than 40 to 60 psi
(276 to 414 kPa):
Check to see whether the sediment filter in the reverse osmosis system
is blocked. Replace the filter if necessary.
Allow the storage tank on the reverse osmosis system to refill after
heavy usage.
If your refrigerator has a water filter, it may further reduce the water
pressure when used in conjunction with a reverse osmosis system.
Remove the water filter. See "Water Filtration System" in the User
Instructions, User Guide, or Use & Care Guide.
If you have questions about your water pressure, call a licensed, qualified
plumber.

Connect Water Supply

Read all directions before you begin.
IMPORTANT:
Plumbing shall be installed in accordance with the International
Plumbing Code and any local codes and ordinances.
The gray water tubing on the back of the refrigerator (which is used to
connect to the household water line) is a PEX (cross­linked
polyethylene) tube. Copper and PEX tubing connections from the
household water line to the refrigerator are acceptable, and will help
avoid off­taste or odor in your ice or water. Check for leaks.
Install tubing only in areas where temperatures will remain above
freezing.
TOOLS NEEDED:
Gather the required tools and parts before starting installation.
Flat-blade screwdriver
⁷⁄₁₆" and ¹⁄₂" open-end wrenches or two adjustable wrenches
¹⁄₄" nut driver
Connect to Water Line
IMPORTANT: If you turn the refrigerator on before the water line is
connected, turn the ice maker OFF.
Style 1 (Recommended)
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long enough to
clear line of water.