System Exclusive Message - Roland GR-33 Manual Del Usuario

Capítulo 11 Apéndices
* Transmitted the operation of onboard WAH function (Pedal 1).
❍
General Purpose #6
STATUS SECOND
BnH 51H
n=MIDI Channel Number:
vv=Control value:
* Transmitted the operation of turning ON or OFF by CTRL pedal.
❍
General Purpose #7
STATUS SECOND
BnH 52H
n=MIDI Channel Number:
vv=Control Value:
* Transmitted the operation of onboard HOLD pedal.
❍
General Purpose #8
STATUS SECOND
BnH 53H
n=MIDI Channel Number:
vv=Control Value:
* Transmitted the operation of CTRL pedal when the Arpeggio is held.
❍
General Effect #1 (Reverb Send Level)
STATUS SECOND
BnH 5BH
n=MIDI Channel Number:
vv=Control Value:
* Transmitted the action of the EXP pedal when the EXP pedal is set to "REV SEND
LEVEL".
❍
General Effect #3 (Chorus Send Level)
STATUS SECOND
BnH 5DH
n=MIDI Channel Number:
vv=Control Value:
* Transmitted the action of the EXP pedal when the EXP pedal is set to "CHO SEND
LEVEL".
❍
RPN MSB/LSB
STATUS SECOND
BnH 65H
BnH 64H
n=MIDI Channel Number:
mm=Upper byte of the parameter data designated by RPN
ll=Lower byte of the parameter data designated by RPN
<<< RPN >>>
Control change includes RPN(registered parameter number), function which are defined by
the MIDI standard.
The GR-33 can transmit only one RPN: pitch bend sensitibity(RPN#0).
RPN Data entry
MSB LSB MSB LSB
00H 00H mmH 00H
* Transmitted when you change the BEND RANGE parameter on SYSTEM menu.
* Not transmitted when BEND REQ SW on SYSTEM menu is set to OFF.
110
THIRD
vvH
0H - FH (0 - 15) 0=ch.1 15=ch.16
00H - 7FH (0 - 127) 00H-3FH=OFF,
40H-7FH=ON
THIRD
vvH
0H - FH (0 - 15) 0=ch.1 15=ch.16
00H - 7FH (0 - 127) 00H-3FH=OFF,
40H-7FH=ON
THIRD
vvH
0H - FH (0 - 15) 0=ch.1 15=ch.16
00H - 7FH (0 - 127) 00H-3FH=OFF,
40H-7FH=ON
THIRD
vvH
0H - FH (0 - 15) 0=ch.1 15=ch.16
00H - 7FH (0 - 127)
THIRD
vvH
0H - FH (0 - 15) 0=ch.1 15=ch.16
00H - 7FH (0 - 127)
THIRD
mmH
llH
0H - FH (0 - 15) 0=ch.1 15=ch.16
Function
pitch bend sensitivity
The transmitted lower byte is always 00H.
●Program change
STATUS SECOND
CnH ppH
n=MIDI Channel Number:
pp=Program Number:
●Pitch Bend Change
STATUS SECOND
EnH llH
n=MIDI Channel Number:
mm,ll=Value:
■
System Realtime Message
●Active Sensing
STATUS
FEH
* This message is always transmitted at about 270msec' interval.
■

System Exclusive message

STATUS DATA BYTES
F0H iiH,ddH,.....,eeH
F0H: System Exclusive
ii=ID Number: 41H (65)
dd,...,ee=Data: 00H-7FH (0-127)
F7H: EOX (End of Exclusive/System Common Message)
* For more details, refer to the page "Roland exclusive message" and Section3 or after.
3. Exclusive Communications
The GR-33 can transmit or receive system and patches parameters using system exclusive
messages. Model ID of exclusive message available on the GR-33 is 00H 30H.Device ID is
fixed at 10H.
When the GR-33 receives an Identify Request inquiry message, it will transmit an Identity
Reply.
●Request Data1 RQ1 (11H)
THis message is to request the GR-33 to transmit its parameters.
The address and size indicate the type and amount of parameters requested.
The GR-33 itself does not send this message.
When the GR-33 receives this message, it responds with appropriate parameters if the
following conditions are satisfied:
1. The address indicated with RQ1 matches with one of the parameter base address of
the GR-33.
2. The requested size is larger than 2.
3. When the Bulk Load standby in System mode.
With these conditions provided, the GR-33 transmits specified parameters in Data Set 1
(DT1) message.
0H - FH (0 - 15) 0=ch.1 15=ch.16
00H - 7FH (0 - 127) 0=prg.1 127=prg.128
THIRD
mmH
0H - FH (0 - 15) 0=ch.1 15=ch.16
00H, 00H - 7FH, 7FH (-8192 - +8191)
STATUS
F7H