Fan; Control Board; Main Functions - Futurelight Spotlite MH-860 Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Fan

The MH-860 is cooled by three axial fans - one each in the projector head and one in the base. The speed of
the fan (and of course the noise) can be continuously reduced if very quiet performance is required.
By the Control Board using the "FAnS" function you can choose 5 types of low fan speed operating. Please
refer to the instructions under SPEC -Special functions.
The Control Board situated on the top side of the MH-860 offers several features. You can simply set the
lighting address, read the number of lamp or unit hours, switch on and off the lamp, run demonstration
sequences, make a reset and also use special functions for manual control and service purposes.
The main menu is accessed by pressing the [Mode] key - press this one so many times until the display
shows message "A001" (with actually stored address). Browse through the menu by the pressing [Up] and
[Down] keys - the display shows step by step these messages: A001, rPAn, rTilt, 16br, Lati, Poti, LAMP,
dEMo, rESE, SPEC. Press [Enter] if you wish to select one of them. The functions provided are described in
the following sections and the function hierarchy is shown below.

Main functions

- DMX 512 Address settings
The letter "A" flashes. Use the [Up] and [down] keys to select required address (001 - 512) and press
[Enter] to confirm or [Mode] to cancel and return to the main menu.
- Pan reverse
This function allows you to invert the Pan-movement. Use the [Up] and [Down] keys to select "On" if you
wish this feature or "Off" if you don't wish this feature and press [Enter] to confirm or [Mode] to cancel and
return to the main menu.
- Tilt reverse
This function allows you to invert the Tilt-movement. Use the [Up] and [Down] keys to select "On" if you
wish this feature or "Off" if you don't wish this feature and press [Enter] to confirm or [Mode] to cancel and
return to the main menu.
- Movement resolution
By this function you can adjust the desired movement resolution 8 or 16 bit. Use the [Up] and [Down] keys to
select 'On' if you wish the 16bit high resolution or "Off" if you wish only 8 bit resolution and press [Enter] to
confirm or [Mode] to cancel and return to the main menu.
Note:
If you adjust the 16 bit resolution the fixture will occupy 16 DMX channels, if you adjust the 8 bit resolution,
the fixture will be operated by only 14 DMX channels. Please, check the DMX protocol.
- Lamp On time
This option enables you to read the total number of hours that the lamp has been powered on. Press [Enter]
or [Mode] to return to the main menu. In order to reset the counter to 0, you have to hold the Up- and Down-
button and press the Enter-button.
- Power On time
By this option you can read the total number of hours that the MH-860 has been powered on. Press [Enter]
or [Mode] to return to the main menu.
- Switch on / off the lamp
Use the [Up] and [Down] keys to select "On" if you wish the switch on the lamp or "Off" if you wish switch
off the lamp and press [Enter] to confirm or [Mode] to cancel and return to the main menu.
- Demo sequences
This function allows you to run a special demo-test sequences without an external controller, which will show
you some possibilities of using MH-860. Press [Up] and [Down] keys to select the "Mod1" or "Mod2"
sequences. The "Mod1" is suitable for projections on the wall, ceilling or ground without any head-
movement, the "Mod2" uses all MH-860 functions and therefore is good for a complete introduction of the
fixture.

Control Board

44

Publicidad

Tabla de contenido
loading

Tabla de contenido