Operation - SPARKY HeavyDuty BR2 10.8Li-C HD Instrucciones De Uso

Operation

FITTING AND REMOVING THE BATTERY PACK
To remove the battery from the machine: press the battery
release buttons (4) and take the battery out of the tool.
WARNING: Always set the forward/reverse
switch (3) in central position before any work on the
the bit,, transport, maintenance and storage.
To install the battery: Insert the charged battery into the
opening at the base of the power tool until the battery is
securely latched with a click.
BATTERY STATE INDICATION (Fig. 2)
The battery state during operation can be checked on
switch (6).
Depending on the number of illuminated LEDs the bat-
tery state is as follows:
3
2
1
1
Blinking light
Blinking light
The direction of decreasing the charge level indicated by
the LEDs is marked on the housing of the power tool.
LED WORK AREA LIGHT
The machine is equipped with LED light (8) to illuminate
the work area and improve visibility when drilling in areas
trigger of switch (6). LED light will automatically turn off 5
seconds after releasing the trigger of switch (6).
Electronic control may turn off the excessively overload-
ed machine in order to protect it. This mode is signalled
by blinking LED work area light (8). The power tool can
be used for its intended purpose after switching it on
again.
REVERSING (Fig. 3)
The extreme position of forward/reverse switch (3) to
the right right (viewed from the rear) is equivalent to anti-
clockwise rotation, the extreme position to the left - to
pressed switch (3) cannot be actuated.
8
EN
Battery capacity: 60 - 100%
Battery capacity: 30 - 60%
Battery capacity: < 30%
Battery capacity: < 20%. The battery
must be recharged.
Problems with battery. The display is
activated upon pressing the trigger of
the switch. It may show one of the fol-
lowing battery states:
Battery has to be
recharged;
Temperature protection
been actuated
be cooled down prior to resuming
operation;
Damaged or unrecognized bat-
tery
cannot be pressed and the machine cannot be operated.
WARNING: Reversing can be performed only
when the spindle is not rotating!
Drilling and tightening screws are performed with lever
in extreme position to the left. Removal of screws is per-
formed with lever in extreme position to the right.
SWITCHING ON - SWITCHING OFF
Switching on:
Switching off:
This power tool is equipped with electric brake. The spin-
dle stops rotating immediately after releasing the switch
lever.
SMOOTH ELECTRONIC RPM CONTROL
low rotation speed, further pressing the switch results in
smooth increase of the rpm to maximum upon reaching
the extreme position.
ADJUSTING THE TORQUE
Rotate the torque adjustment collar (9) behind the chuck,
to adjust the torque to each of 20 settings.
The range of 20 torque settings allows better control
when using the drill as a screwdriver thus preventing
over-tightening of the screws.
The numbers circling the collar are used to indicate the
level of torque. The larger the number on the collar, the
higher the torque. To select any of the numbers, rotate
the collar (9) until the desired number aligns with the ar-
has
row head indicator on the housing of the machine.
Screwdriving
Set the torque adjustment collar (9) against one of 20
positions.
Select low setting range for working with small screws
1
or in soft materials.
÷
Select high setting range for working with large screws
20
or in hard materials.
BUR2 10.8Li-C HD:
Set the operation mode selector switch (12) against the
symbol "screw".
Drilling
Set the torque adjustment collar (9) against this symbol
to choose drilling in metal, wood, etc.
The power tool is equipped with an electric brake. The
spindle stops rotation immediately after the switch trig-
ger has been released. At overloading in drilling mode
release the switch immediately to prevent prolonged
overloading and overheating the motor.
BUR2 10.8Li-C HD:
Set the operation mode selector switch (12) against this
symbol.
Impact drilling (BUR2 10.8Li-C HD:)
Set the operation mode selector switch (12) against
this symbol to select impact drilling in bricks, cement,
tiles, etc.
-