Know Your Product - SPARKY HeavyDuty BR2 10.8Li-C HD Instrucciones De Uso

done previously. DO NOT CONTINUE to use under
Li- ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging proce-
dure does not damage the battery.
If the battery pack does not charge properly:
(1) Check current at receptacle by plugging in a lamp
or other appliance.
(2) Move charger and battery pack to a location where
the surrounding air temperature is approximately 15°C–
25°C).
(3) If charging problems persist, take or send the tool,
battery pack and charger to your local service centre.
To ensure the longest battery life and best battery
performance, always charge the battery when the air
temperature is between 15–25°C. Do not charge the
battery pack when the temperature is below 5°C, or
safety rule could cause serious damage to the bat-
tery pack.
The charger and battery pack may become warm to
touch while charging. This is a normal condition, and
does not indicate a problem.
To prevent overheating, do not charge battery packs
in direct sunlight in hot weather or near heat sources.
Do not charge inside a box or container of any kind.
The battery must be placed in a well ventilated area
during charging.
When the battery is defective, liquid can escape and
come into contact with adjacent components. Check
any parts concerned. Clean such parts or replace
them, if required.
Do not incinerate the battery pack even if it is seriously
damaged or can no longer hold a charge. The battery
pack can explode in a fire.
To facilitate the cooling of the battery pack after use,
avoid placing the charger or battery pack in a warm
environment such as in a metal shed, or an uninsu-
lated trailer.
BATTERY CHARGING (Fig. 1)
Insert the plug of the charger in the socket. The green
LED light on the charger indicator (11) will start to glow
thus indicating mains voltage.
Insert the battery (5) in the charger socket (10).
A new battery will work properly after five cycles of
charging and discharging. Charge and discharge a
battery, which is not used for a long time, for two to
three times to function well.
When the battery working time is remarkably short de-
spite full charging, the life of the battery may be over.
Replace the battery immediately.
Charging indication:
The green LED light starts to glow upon plugging the
charger in the mains.
The green LED light starts to blink after the battery
has been placed in the charger, thus indicating the
beginning of the charging process.
During the charging process the charger and battery
might become warm. This is a normal condition, and
does not indicate a problem.
The green LED light starts to glow constantly after
completion of charging.
Original instructions
The charger features thermal overload protection for the
battery. Nevertheless we recommend withdrawing the
battery from the charger upon expiring of the charging
time. You may use additionally an electric timer in order
to control the charging time.
State description
Constantly glowing Ready-to-charge state
green light When there is no battery pack in-
serted in the charger, green light
indicates ready-to-charge state.
Blinking green light: Charging
Battery pack is being charged.
Constantly glowing Fully charged battery pack
When there is a battery pack in-
green light
serted in the charger, green light
indicates that it is fully charged.
Constantly glowing Battery temperature is out of
red light the admissible charging tem-
perature range 0÷45
Move the charger with battery to
another premises with appropri-
ate environmental temperature.
Once the temperature reaches the
admissible charging temperature,
the charger automatically switches
to charging mode.
Blinking red light: Fault
In failure mode charging is not pos-
sible. The reason for failure may
be one of the following:

Know your product

Before using the power tool, familiarize yourself with all
operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Keyless chuck
2. Speed selector switch
4. Battery release buttons
5. Battery
7. Battery state indicator
8. LED light
9. Torque adjustment collar
10. Charger
11. LED charge state indicator
12. Operation mode selector switch
o
C
Battery pack is not inserted
properly;
Battery pack terminals are
dirty;
Damaged battery pack;
Unrecognized battery pack.
7
EN