Inglesina Classica Balestrino Manual De Instrucciones página 15

FRAME
ASSEMBLY OF THE COMPONENTS
1 Check that all components of the frame are present:
frame base A, handle B, two front wheels C, two rear wheels
D.
OPENING OF THE FRAME BASE
2 A by moving upwards both springs
E and F.
ASSEMBLY OF THE HANDLE
3 Insert the pins G positioned outside of the frame in the
proper holes H on the handle B.
4 Push inwards.
5 Lower both locking push-buttons K in the proper seat,
until you can hear a coupling click.
6 CAUTION: Try to pull the handle outwards to make
sure that the coupling has properly occurred.
7 Push the handle downwards until you hear a coupling
click at the pins J (see fig. 4).
ASSEMBLY OF THE REAR WHEELS
8 Caution: Two of the supplied wheels are bigger and
equipped with a brake rack. These two wheels D have to
be assembled on the rear axle of the frame near to the
brake bar L.
9 Make sure that the brake bar L is positioned upwards (in
position of brake-release).
10 Lift the frame base A and seize one of the rear wheels D.
Pull upwards the lever M located on the wheel and insert the
wheel in the pin N.
11 Push the wheel D inwards, release the lever M until you
hear a click signalling the occurred coupling.
12 Verify that the wheel is correctly coupled by pulling it
outwards. Repeat the procedure also for the other rear
wheel.
ASSEMBLY OF THE FRONT WHEELS
13 Caution: Two of the wheels supplied with the frame
are smaller. These two wheels C have to be assembled on
the front axle.
14 Lift the frame base A and seize one of the front wheels C.
Pull upwards the lever M located on the wheel and insert the
wheel in the pin N.
15 Push the wheel C inwards and release the lever M until
you hear a click signalling the occurred coupling.
16 Verify that the wheel is correctly coupled by pulling it
outwards. Repeat the procedure also for the other front
wheel.
17 Make sure that the frame is assembled in the correct way
- see figure.
HOW TO ENABLE/DISABLE THE BRAKE
18 To insert the brake, lower the bar L, by pushing with the
foot downwards.
Caution: Always check that the brake has been correctly
enabled.
19 To disable the brake, lift the bar L by pushing with the
foot upwards.
SPACE-SAVING POSITION
20 In order to reduce the overall dimensions of the frame,
the handle B can rotate around the pin G. Simultaneously
INSTRUCTIONS
push forwards both levers P of the sleeve Q.
21 Push the handle B forwards and let it rotate until it is
positioned as in figure.
HOW TO CLOSE THE FRAME
22 With braked frame (see fig. 18) lift both locking push-
buttons K to release them from the collars of the pin G.
23 Simultaneously push forwards both levers P of the slee-
ve Q.
24 Pull outwards both the sides of the handle B in order to
extract it from the pins G.
25_26 Remove the front wheels C lifting the proper levers M
and extracting the wheels from the pin N.
27_28 Lift the brake bar (see fig. 9). Remove the rear wheels
D by lifting the proper levers M and extracting the wheels
from the pin N.
29 Close the springs E and F by pulling them inwards.
COUPLING OF THE BAG
30 Make sure that the frame is correctly assembled and the
brake enabled (see fig. 18). Rotate clockwise the frame hol-
ding hooks S located on both sides of the frame. The red
angle becomes visible.
31 Take the bag holding it firmly by the handles T. Insert all
four pins U of the bag in the proper openings Z of the frame.
32 Caution: Always make sure that the bag is correctly
positioned.
33 Close both hooks S by rotating them counter-clockwise.
ADJUSTMENT OF THE CAPOTE
34_35 To lower the capote, lift the lateral hooks O (see fig.
34) and push it downwards (see fig. 35).
36_37 To lift the capote, pull it upwards (see fig. 36) and
lower the hooks O until you hear a click signalling the occur-
red coupling (see fig. 37).
ADJUSTMENT OF THE SEAT BACK
38 Lower the capote (see fig. 34_35). Lift the mattress and
hook the lever R in the proper seat V.
39 Make sure that the lever is correctly inserted.
HOW TO RELEASE THE BAG
40 Make sure that the brake is correctly inserted (see fig.
18). Rotate both frame holding hooks S counter-clockwise to
release the pins U of the bag (see fig. 30).
41 Extract the bag from the openings Z.
ASSEMBLY OF THE OBJECTS HOLDING BASKET
43 Hook the end of the basket foreseen with spring to the
rear axle of the frame X (see fig. 42).
44 Pull the basket towards the front part of the frame and
hook it to the front axle Y (see fig. 42).
COUPLING/RELEASING OF THE CARRYING SEAT AND
SEAT HUGGY
seat Huggy, refer to the related instructions.
4
EN