Important - Harman JBL AVR 101IN Manual Del Propietário

AVR
Front-Panel Controls, continued
Power indicator/Power button: The AVR has three different power modes:
• Off (Power indicator glows solid amber): The Off mode minimizes energy consumption
when you're not using the AVR. When the AVR is off, it will not automatically turn on
or play audio in response to a DLNA DMR stream from a networked device. When
the AVR is off, pressing the Power button turns it on. To turn the AVR off when it is on,
press the Power button for more than three seconds. The Front-Panel Display will
indicate "Your device is switched off" for two seconds, then will switch off.
NOTE: You can use the System Setup menu to set the AVR to automatically enter
the off mode after it has been in the Sleep mode for a certain period of time. See
System Settings, on page 29.
• Sleep (Power indicator glows solid amber and front-panel display indicates "Device
sleep"): The Sleep mode powers-down some of the AVR's circuitry, but allows the
AVR to automatically turn on and play audio in response to a DMR stream from a
networked device. When the AVR is in Sleep, pressing the Power button turns it on.
To put the AVR into Sleep when it is on, press the Power button for less than three
seconds. The front-panel display will indicate "Your device is going to sleep" and
then indicate "Device sleep" while the AVR is in the Sleep mode.
NOTE: The AVR will automatically enter the Sleep mode after 30 minutes of no audio
signal or user control input, unless USB, iPod, Home Network, vTuner or DLNA DMR
is active. In these cases, the AVR will automatically enter the Sleep mode after the
number of hours set in the Auto Power Off system setting. See System Settings,
on page 29.
• On (Power indicator glows solid white): When the AVR is on it is fully operational.
Headphone jack: Connect a 1/4" stereo headphone plug to this jack for private
listening.
RDS button (AVR 101IN only): When listening to an FM radio station that broadcasts
RDS information, this button activates the various RDS functions.
USB port: The USB port can be used to play audio files from an Apple iOS
connected to the port, and can also be used to play MP3 and WMA audio files from a USB
device inserted into the port. Insert the connector or device into the USB port oriented so
it fits all the way into the port. You may insert or remove the connector or device at any
time – there is no installation or ejection procedure.
You can also use the USB port to perform firmware upgrades. If an upgrade for the AVR's
operating system is released in the future, you will be able to download it to the AVR using
this port. Complete instructions will be provided at that time.
IMPORTANT: Do not connect a PC or other USB host/controller to this port, or you
may damage both the AVR and the other device.
Channel Volume Adjust button: Press this button to activate the individual channel level
adjustment. After pressing this button, use the Up/Down buttons/Tuning buttons to select
the channel for adjustment and use the Left/Right buttons to adjust the channel's level.
Audio Input button: Press this button to change the audio input connection for the current
source. Use the Left/Right buttons to cycle through the available input connections, and
press the Set button to assign the currently-displayed connection to the source.
IR sensor: This sensor receives infrared (IR) commands from the remote control. Make
sure that the sensor is not blocked.
Set button: Press this button to select the currently highlighted menu item.
Left/Right buttons: Use these buttons to navigate the AVR's menus.
Front-panel display: Various messages appear on this two-line display in response to
commands and changes in the incoming signal. In normal operation, the current source
name appears on the upper line, while the active surround mode is displayed on the
lower line. When the on-screen display menu system (OSD) is in use, the current menu
settings appear.
Up/Down buttons/Tuning buttons: Use these buttons to navigate the AVR's menus.
When the radio is the active source, use these buttons to tune stations according to the
setting of the Tuning Mode button (see above).
Surround Mode Category button: Press this button to select a surround-sound category.
Each press changes the surround-mode category: Auto Select, Virtual Surround, Stereo,
Movie, Music and Game. To change the specific surround-sound mode within the
category, use the Surround Mode Select buttons. See Audio Processing and Surround
Sound, on page 27, for more information about surround modes.
Surround Mode Select buttons: After you have selected the desired surround-mode
category, press these buttons to select a specific mode within the category, such as to
change from Dolby ® Pro Logic
mode availability depends on the nature of the source input signal, i.e., digital versus
analog, and the number of channels encoded within the signal.
Source Select buttons: Press these buttons to select the active source.
Volume knob: Turn this knob to raise or lower the volume.
device
®
Front-Panel Controls
® II Movie mode to DTS ® NEO:6 Cinema mode. Surround
5