Inspection And Maintenance - AL-KO solo 548 K Traducción De Las Instrucciones Originales

9. INSPECTION AND MAINTENANCE

NOTE
See the engine instruction manual for the details of the maintenance of
the engine.
9.1 Cleaning
・ Wipe dirt off when this machine and the safety labels get dirty.
Do not directly spray water with a hose, etc. since it may cause a
・
machine failure.
・ Wipe with a dry rag after cleaning, and then wipe the metal surface
with a rag soaked with oil.
Clean the grass bag while spraying water with a hose. Use it after drying.
・
9.2 Checklist
Operating hours
Check
Engine oil
(8.1.1, 9.4) Exchange
Air cleaner
Cleaning
(9.5)
Loose bolt
Check
(9.8)
Fuel
Refueling
(8.1.3)
Ignition plug Cleaning
(9.6) Adjust
Blade
Check
(9.7)
Blade bolt
Check
(9.7.1)
Grass bag Check
(8.1.4) Cleaning
Throttle wire
Adjust
Drive clutch wire
Adjust
Blade wire Adjust
Check
Gearshift wire
Adjust
Valve clearance Adjust
Combustion chamber Cleaning
Fuel tank Cleaning
Strainer Cleaning
Fuel tube Check
* Exchange oil after using the machine for 25 hours only for the first time
after purchase.
After that, exchange oil at 50-operating hour intervals according to the
degree of dirtiness.
** Maintenance techniques and special tools are necessary for this check
item. Therefore, consult our distributor near you.
The numbers in ( ) show the sections in this manual to be referred.
9.3 Lubrication to Each Part
Regularly lubricate each bearing with an oilcan to keep the smooth operation
of each part.
9.4 Exchanging Engine Oil
NOTE
Extract gasoline first before tilting the engine to drain its oil.Treat and
dispose the drained engine oil properly according to the law in each country.
Time
Every
time 25 50 100
○
○
★
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
★★
○
★★
○
★★
○ ★★
○
EN
Take sufficient caution not to get burnt since the engine and the
muffler are very hot right after the engine stops.
1. Remove the oil tank cap.
(See Section 8.1.1)
2. Drain the engine oil from the
drain port. (See Fig. 27)
3. Fill with fresh engine oil after
drainage is complete.
9.5 Air cleaner (See Fig. 28)
Remove Mounting bolts (a) and
1.
open Cover (b).
Clean Element (c) if it is very dirty.
2.
3. Return Element (c) to its original
position, and close Cover (b) with
Mounting bolts (a).
9.6 Ignition Plug
1. Remove Plug cap (Q).
(See Fig. 29)
2. Remove Ignition plug (P) with the
attached plug wrench. (See Fig. 30)
3. Exchange Ignition plug (P) if a great
amount of carbon is adhered to it or its
insulator is cracked or damaged.
4.
Remove the carbon adhered to the
electrode, and adjust the electrode
(See Fig. 31)
clearance to 0.7 mm.
5. Install Ignition plug (P) and Plug cap (Q).
9.7 Blade
NOTE
Incline this machine with the carburetor side of the engine positioned upside.
9.7.1 Checking the blade mounting bolts
WARNING
Stop the engine and remove the ignition plug when you check the blade.
Wear thick gloves when you check or attach or detach the blade.
Chip
New Blade
13
Oil pan
Drain
Q
Plug Wrench
P
Bend Wear
Fig. 32
Fig. 27
Fig. 28
Fig. 29
Fig. 30
Fig. 31