Troubleshooting - Essentiel EPGZ 2 Instrucciones De Uso

• Spiders and insects can nest in burner tubes and block the gas supply or cause fire flashbacks.
To avoid damaging the appliance and causing a dangerous situation, check and clean the burners
frequently.
• Check that the gas bottle is completely full.
•
• Set all burner control knobs to the "
• Check for possible gas leaks using a solution of water and washing-up liquid. Refer to the "Gas
cylinder connection - Leak test" section.
• Make sure the griddle plate is clean before use.

troubleshooting

Abnormalities Possible cause
NEVER DISASSEMBLE THE GAS MANIFOLD
BUILT INTO THE GRIDDLE (located behind the front control panel),
THE VALVES, INJECTORS OR ANY PART PROTECTED BY THE MANUFACTURER
The flame is lit on 2
Blocked burner
burners, but not on the
(venturi tube) and/
3rd, or on 1 burner, or
or injector(s)
not on the 2nd.
Flames come out Immediately shut off the gas supply, taking all necessary precautions.
through one of the Clean the previously dismantled burner and injector directly (without prior
buttons on the control testing) for the button in question with compressed air (usually available
panel. from your retailer).
56
V.1.0
troubleshooting
OFF" position (stop) then connect the gas supply.
Solution
IMPORTANT
Remove the inoperational burner and replace it
for the duration of the test with one of the other
burners (which works), which has been dismantled
beforehand as well. Perform a test on the ignition:
- If the burner (the "replacement" used for the test)
does not light up:
This means that it is the injector that is blocked.
Clean it with compressed air (usually available from
your retailer).
- If the burner (the "replacement" used for the test)
lights up:
This means that the initial burner is blocked. Clean
it with compressed air or with a pipe cleaner (usually
available from your retailer).
Abnormalities Possible cause
a) Clean each of the previously dismantled burners and injectors directly
(without pre-testing) with compressed air (usually available from your
retailer).
b) Gas cylinder Open the gas cylinder valve (further) to release it into
valve closed, the appliance's circuit.
I can no longer turn
insufficiently open Purge the regulator by pressing the button
on my appliance after
or not purged. on the regulator at the gas cylinder.
the first use or after
several uses.
Try to turn the appliance back on with a new gas
None of the burners
c) Empty gas cylinder.
on my appliance
cylinder If the device turns on again with the new cylinder, it
lights up, on first use,
means that your original cylinder was empty.
or after several uses.
Try to switch the appliance on again with another
d) Connection
connection hose.
hose for the
If the appliance turns on again, it means that your
cylinder-appliance
original hose was blocked: Clean it with compressed
is obstructed
air (usually available from your retailer).
Gently move the tip of the piezo so that it is located
about 3 - 4 mm from the burner and at a hole in the
Integrated
The appliance's burner.
electronic ignition
burners do not light If this does not work, it means that the Piezo is
system (Piezo)
using the button defective. Contact your retailer.
incorrectly
(piezo) but with a
positioned or
match, it works.
defective.
Dismantle the burner with the yellow flames and
replace it for the duration of the test with one of
the other burners (which works), which has been
dismantled beforehand. Perform an ignition test:
• If the burner (the "replacement" used for the test)
also has yellow flames:
Blocked burner
This means that it is the injector that is not correctly
The flame turns yellow (venturi tube) or
positioned. There is therefore too much air in the air/
instead of blue. injector incorrectly
gas ratio, which causes yellow flames to appear.
positioned.
Contact your retailer.
• If the burner (the "replacement" used for the test)
does not have yellow flames:
This means that the initial burner is blocked. Clean
it with compressed air or a pipe cleaner (usually
available from your retailer).
Solution
57
V.1.0
troubleshooting