Service Menu; Setup Of The Internal Watch And Of The Timing; Feature Of The Water Heating System - TECO LR400 Manual De Instrucciones

SPECIAL PROGRAMS
7.

sErvICE mENU

RESET + 30" → 10" WASHING CYCLE
Keep depressed the "RESET" + "DRY" buttons for 5 seconds to enter in the multi-page service menu.
RESET + 120" → 600" WASHING CYCLE
RESET + DRY → SERVICE PAGE
RESET + WHS → FAST WATER HEATING
Some pages allow to modify preset wheel washer parameters. In this case, the message will flash on the upper line of the display, whereas, on the
RESET + 60" → GRANULE COLLECTION
bottom line will appear the value to be set.
Press "RESET" to save the setting value and move to the next setting in the same page or to the next page.
Press "DRY" to move to the next page without saving the setting value.
Press "STOP" to exit the menu.
110mm
Otherwise, through other pages, it is possible to display some information about the wheel washer status. In this case, the information value is
displayed on the bottom line of the display.
Press "RESET" or "DRY" to move to the next page.
The service pages available are the following:
- Setup of the internal watch and of the timing feature of the water heating system.
- Low power mode.
- Setting of washing cycle number before "CLEAN" message.
- Total number of performed washing cycles.
- Software release.
7.1 sETUP oF ThE INTErNAL WATCh ANd oF ThE TImINg FEATUrE oF ThE WATEr
hEATINg sYsTEm
To setup the internal watch and the timing feature for the water heating system, if present proceed as follows:
• Press the green "RESET" button and keep it depressed.
• Press the "DRY" button and keep both the "RESET" and the "DRY" buttons depressed for at least 5 seconds.
• The LCD display will show "TIME START END *" on the first line.
• Release both the "RESET" and the "DRY" button.
"TIME" will start flashing on the first line of the LCD display and "00:00" will show on the second line. If the internal watch has already been set
previously, the current time will show. At this point the current time can be set for the internal watch.
• Press and release the " 30" " button to increase the hours of the time shown on the second line by one hour. Keep the " 30" " button de
pressed for progressively increasing the hours of the time shown on the second line.
• Press and release the " 60" " button to decrease the hours of the time shown on the second line by one hour. Keep the " 60" " button
depressed for progressively decreasing the hours of the time shown on the second.
• Press and release the " 90" " button to increase the minutes of the time shown on the second line by one minute. Keep the " 90" " button
depressed for progressively increasing the minutes of the time shown on the second line.
• Press and release the " 120" " button to decrease the minutes of the time shown on the second line by one minute. Keep the " 120" "
button depressed for progressively decreasing the minutes of the time shown on the second line.
• Press the "STOP" button at any time for exiting to the main operation page without saving the time set.
• Press the "RESET" button to save the set time as the current time and proceed to setting the water heating system start time.
"START" will flash on the first line of the LCD display and "00:00" will show on the second line. If the start time for the water heating system has
already been set previously, the current start time will show. At this point the start time can be set for water heating system timing feature.
• Press and release the " 30" " button to increase the hours of the time shown on the second line by one hour. Keep the " 30" " button de
pressed for progressively increasing the hours of the time shown on the second line.
• Press and release the " 60" " button to decrease the hours of the time shown on the second line by one hour. Keep the " 60" " button
depressed for progressively decreasing the hours of the time shown on the second.
• depressed for progressively increasing the minutes of the time shown on the second line.
• Press and release the " 120" " button to decrease the minutes of the time shown on the second line by one minute. Keep the " 120" "
button depressed for progressively decreasing the minutes of the time shown on the second line.
• Press the "STOP" button at any time for exiting to the main operation page without saving the start time set.
• Press the "RESET" button to save the set start time and proceed to setting the water heating system end time.
"END" will flash on the first line of the LCD display and "00:00" will show on the second line. If the end time for the water heating system has already
been set previously, the current start time will show. At this point the end time can be set for water heating system timing feature.
• Press and release the " 30" " button to increase the hours of the time shown on the second line by one hour. Keep the " 30" " button de
pressed for progressively increasing the hours of the time shown on the second line.
• Press and release the " 60" " button to decrease the hours of the time shown on the second line by one hour. Keep the " 60" " button
depressed for progressively decreasing the hours of the time shown on the second.
• Press and release the " 90" " button to increase the minutes of the time shown on the second line by one minute. Keep the " 90" " button
depressed for progressively increasing the minutes of the time shown on the second line.
• Press and release the " 120" " button to decrease the minutes of the time shown on the second line by one minute. Keep the " 120" "
button depressed for progressively decreasing the minutes of the time shown on the second line.
• Press the "STOP" button at any time for exiting to the main operation page without saving the end time set.
• Press the "RESET" button to save the set end time and proceed to activate or deactivate the timing feature of the water heating system.
"*" will flash on the first line of the LCD display and "OFF" will show on the second line. If the activation state for the water heating system has alre-
ady been set either to ON or OFF previously, the current activation state will show. At this point the activation state for water heating system timing
feature can be set.
• Press and release the " 30" " button to change the activation state for water heating system timing feature either from OFF to ON or from
OFF to ON.
• Press the "STOP" button at any time for exiting to the main operation page without saving the activation state for the water heating system timing
feature set.
• Press the "RESET" button to save the set activation state for the water heating system timing feature and exit to the main operation page.
Adesivo cod. 4-602877
UNICA FUSTELLA - DUE ADESIVI SEPARATI
D
= Min 10mm
AIR
D = 65mm
43