Changing The Water Inside The Wheel Washer - TECO LR400 Manual De Instrucciones

The granulate collection basket (Fig.4), delivered along with the wheel washer, is to be used for this purpose.
To correctly place the granulate collection basket is provided with a V shaped seat on its lower side and with a support tab out side of each perfora-
ted sidewall.
To easily move the granulate collection basket, this is provided with two plastic handles, one laying outside of the front wall of the collection basket
and the other laying inside the rear wall of the collection basket.
To remove the plastic granulate from the wheel washer:
• Turn on the wheel washer acting on the main switch on the front of the wheel washer.
• Open the washing chamber door and place the granulate collection basket inside the washing chamber letting the V-shaped notch on its
bottom engage with the front horizontal roller spanning between the sidewalls of the washing chamber and the two support tabs on the
sidewalls of the collection basket rest each on one of the rear inclined support rollers mounted on the sidewalls of the washing chamber.
• After placing the collection basket inside the washing camber check that the two support tabs on its sidewalls correctly rest on the rear
inclined support rollers mounted on the sidewalls of the washing chamber (Fig.11).
SPECIAL PROGRAMS
CAUTION
once the collection basket has been correctly placed inside the washing camber the two openings on the sidewalls of the collection
basket shall face each one the washing nozzle mounted on the sidewalls of the washing chamber. RESET + 30" → 10" WASHING CYCLE
RESET + 120" → 600" WASHING CYCLE
• Close the washing chamber door.
RESET + DRY → SERVICE PAGE
• Keep depressed the "RESET" + "60" buttons to activate the specific cycle for granule collection.
RESET + WHS → FAST WATER HEATING
RESET + 60" → GRANULE COLLECTION
• The blue LEDs over the "30" and "120" button switch on.
• While the pump motor rotates, the water inside the wheel washer body will be drawn from the pump along with the plastic granulate floa
110mm
ting inside it and will be sent to the washing nozzles that will divert it inside the collection basket through the openings on its sidewalls.
• Water and granulate will be collected then inside the collection basket.
• After 10 minutes, the pump stops rotating without activating the drying nozzles.
• The two perforated sidewalls of the collection basket will let the water drain back to the wheel washer body while retaining the plastic
granulate inside the collection basket.
NOTE:
Once the long washing cycle has completed most of the granulate floating in the water inside the wheel washer body will be collected inside the
collection basket.
Wait for 5 minutes after completion of the long washing cycle to let as much water as possible drain back to wheel washer body then remove the
collection basket form the wheel washer along with granulate collected inside it by holding it through the two handles.
WARNING
once the collection basket is filled with granulate its weight will be considerably higher.
removing of the collection basket from inside the washing chamber once it is filled with granulate is best performed by two people, each
holding one of the two handles.
• Level the granulate inside the collection basket manually and check the level of the granulate does not lay less than 10 mm (0,4") below
the red indicator positioned on the right side of the basket.
• If this is the case the amount of granulate is low. Add new granulate into the collection basket until it reaches the requested level.
9.2

CHANGING THE WATER INSIDE THE WHEEL WASHER

Once the wheel washer has performed the wheel washing cycle, the LCD display will show "CLEAN" on the first line. It is time then to drain the
water inside the wheel washer body, rinse the wheel washer body and fill it again with clean water.
CAUTION
during the first washing cycles burrs from machined parts of the wheel washer and the plastic granulate will detach and settle into the
water.
It is strongly suggested to perform an intermediate water change and rinsing of the wheel washer body and the plastic granulate, as
explained further in this paragraph, to achieve best washing performance.
such an intermediate water change should be performed after the wheel washer has performed about 100 washing cycles and the LCd
display shows "rEAdY" on the first line and 400 on the second line.
WARNING
draining waste water from the wheel washer body to the sewage may be subject to limitations in your country.
Always follow local law and regulation when draining waste water from the wheel washer body to the sewage.
48
Adesivo cod. 4-602877
UNICA FUSTELLA - DUE ADESIVI SEPARATI
11
D
= Min 10mm
AIR
D = 65mm