Installation And Transport; Special Product Features; Machine Details - Metabo KGS 303 Manual De Uso

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

ENGLISH
32

4. Installation and transport

A
CAUTION
Do not carry the machine by the
handle; the handle is not designed
to bear the weight of the entire
machine.
When
carrying
machine, hold it on both sides of
the base.
Installation
1.
The machine is heavy. Carefully lift
it out of its shipping carton with the
help of another person.
(The
manufacturer
that you keep the shipping carton
and all packing materials in case the
machine needs to be shipped for
service or repair. If you discard the
packing materials, do so in observ-
ance of and in compliance with all
environmental laws, rules and regu-
lations regarding disposal and recy-
cling that apply at your site.)
3
Note:
Do not install rubber feet if the
machine is going to be mounted on the
optional machine stand. The machine
stand is not included in standard deliv-
ery, but can be purchased separately.
For more information, see chapter 11.
2.
Turn the machine over to install the
rubber feet:
The feet must be accessible from
all directions.
12
Before proceeding, be sure that
the machine is standing firmly in
place even while tipped over.
3.
Fit the nut (36) into the hole on the
bottom of the rubber foot.
4.
Insert the Allen head screw (33) into
the machine's foot from the top. Fit
the washer (34) on the screw (33)
and attach the rubber foot (35) with
the previously inserted nut (36) to
the screw (33) by hand and start to
tighten.
5.
To do so hold the screw (33) with
the 6mm Allen wrench.
6.
Hand tighten only!
the
33
7.
Place the machine on a flat and
sturdy surface, large enough to
allow for all necessary movements
and adjustments.
All four feet must firmly rest on
the base.
The ideal height for the base is
32 inches.
recommends
The machine must remain stable,
in particular when cutting work
pieces which could cause it to tip.
8.
Push the sawhead assembly slightly
down and pull the transport locking
pin (37) out.
38
Transport
1.
2.

5. Special Product Features

34
35
36

6. Machine Details

ating elements of the machine are intro-
duced.
The proper use of the machine is
described in chapter 8, "Operation".
Read this chapter in its entirety before
using the saw for the first time.
ON/OFF switch
37
The transport locking pin (37) must
be inserted for transport.
Depending on what kinds of cuts
were made previosuly, it may be
necessary to adjust the limit screw
(38) for the adjustment of the cutting
depth. This allows the saw head to
be fully lowered, after which the
transport locking pin (37) can then
be inserted.
96 cutting angle range for bevel
cuts (48 left through 48 right) with
five preset stops.
110 cutting angle range for miter
cuts (50 left through 60 right) with
ten preset stops.
Soft start.
Cutting depth adjustment for making
grooves with integrated limit screw.
Easy mobility due to lightweight con-
struction.
Precise and sturdy die-cast alumin-
ium construction.
TCT saw blade.
Easy saw blade change. The saw
blade can be held with the saw
blade lock. No disassembly of the
protective devices required.
Maximum cutting depth 3 3/16".
Maximum cutting width 11 1/4".
Ergonomic and easy for both left-
handed and right-handed operation.
Installation of auxiliary fence possi-
ble.
3
Note:
In this chapter the essential oper-
To turn the motor on, press and hold
the ON/OFF switch (39) in the han-
dle. To stop the motor, release the
ON/OFF switch.

Publicidad

Tabla de contenido
loading

Tabla de contenido