Normal Operation - Vimar ELVOX 41016 Manual Del Instalador

41016
swipe, the status LED will rapidly flash orange during
the processing stage and then will change to green, if
the finger swipe is successful, or red if is not. The same
status LED will then turn to steady orange to indicate
that the device is waiting for another finger swipe.
4. After all 3 acquisitions are completed successfully, the
status LED and the 2 function LEDs will turn green for
about 1 second: this indicates that the fingerprint has
now been registered and saved in the database and the
result is signalled by a SaveProg message.
5. The device then prepares for acquisition of the next
fingerprint/user, either returning to the check phase, if
"Check Enabled" is selected, with the corresponding
indication on the function LEDs, or, if not, entering
directly into the acquisition phase (status LED lit orange)
waiting for the 3 finger swipes.
6. If a period of 10 seconds elapses without a finger swipe,
the device will exit the check or acquisition phase
and SaveProg will display the message "acquisition
timeout". The device will then return to normal operating
mode (with only the status LED lit blue), ready to accept
a new command from SaveProg or to identify a finger
swipe.
5.2 Manual Management
You can also implement the following procedure to register
a user print:
1. Press a fingerprint programmed as "installer";
... ...
2. Within 5 s, press the print to be recorded as "user"; while
waiting the orange LED remains on.
3. To complete the fingerprint recording, the finger must be
pressed 3 times. When recorded correctly, the central
LED turns green for an instant. After all 3 acquisitions
the central led and the 2 leds below turn green for ap-
proximately 1 second.
4. The procedure is repeated from point 2, repeating the
acquisition for any other users (the central LED turns
orange and stays on).
If the acquisition is not correct, the central LED turns red for
a few seconds. The operation must be repeated. After 5 s
the procedure is exited and the central LED turns blue again.
To delete prints you always need to use SaveProg.
6

Normal operation

The fingerprint recognition is indicated by the module with the
status LED and the two function LEDs both lit in GREEN for
approximately 1 second.
The NON-recognition of a fingerprint is indicated by the mod-
ule with the status LED and the two function LEDs both lit in
RED for approximately 1 second.
Depending on the set configuration, the actions associated
to the local button and the fingerprint recognition are respec-
tively:
• Local button pressed or with fingerprint recognised:
- with A/V ENABLED mode a notice is sent to the A/V mod-
ule which will run the configured command.
8
- in "local CA input" ENABLED mode, the "F1" relay is im-
mediately switched on.
7 Updating
The device is updated with Winboot via the USB connec-
tion. To upgrade you need to disconnect the device from the
auxiliary power supply and from the other modules, connect
the USB to the PC and start the update. During the updating
time (30sec) the LEDs are switched off and when restarting
after the update the LEDs may change status with different
colours.
8 Using the fingerprint reader
The best results are obtained using the middle finger
with the index and ring fingers straight.
Place the finger joint di-
rectly on the sensor
-
·�-:.�
.
,· .
-
·�-:.�
.
,· .
Then placing the finger on the
scanner, the ideal position is with
all fingers straight and close to-
gether.
Move (the whole hand) down-
wards on the sensor, without
bending the finger.
-
Take care to slide the finger at the
·�-:.�
.
,· .
right speed. CAUTION: The whole
movement should take 1 - 1.5
seconds.
Do not move the position of the
fingers while scanning (e.g. by
bending the finger joint).
You do not need to put any pres-
sure on the scanner.
EN
Make sure the finger is po-
sitioned in the centre of the
scanning area, between
the two finger guide edges.
... ...
Place the finger fully stretched so that
it adheres perfectly to the sensor.
-
·�-:.�
.
,·
... ...
... ...
.