Technical Features - Schneider Airsystems AM 2-10 F1 Micro Manual De Instrucciones

ELECTRICAL HOOK-UP (fig. 3)
• The mains cable should have a cross-section suitable for
the machine power and should include no. 3 phase wires, no. 1
neutral cable and no. 1 earth wire.
• Between the mains cable and the compressor control panel a
fused switch near the point where the cables go into the machine is
absolutely necessary. The switch should be at least at 1.7 m from
the ground.
• The switch (A) should be easily reached by the operator. The
cables should be of the approved type and installed with the following
grade of protection: minimum IP44
N.B. To determine the cables cross-section and the type of
switch refer to the data reported on the technical table.
technical characteristics
Work pressure
Pump group
Rotation speed of the towing rotor
Air outflow rate (according to ISO 1217 annex C)
Oil quantity
Quantity of top up oil
Heat carried
Fan flow rate
Oil residuals in the air
Electric motor
Nominal Input
Max input power from the mains
Maximum start ups per hour
Ambient temperature limit
Sound pressure (according to Pneurop/Cagi PN2CPTC2) dB(A)
electrical data
Voltage power supply
Auxiliary voltage
Current input at start up
Max current input
Electric motor protection degree
Insulation class
Service factor
Protection devices
Oil circuit max temperature
Pre-alarm oil temperature calibration
Thermostat calibration
Thermal motor relay calibration
Safety valve calibration
Dimensions
Length
Width
Height
Weight
Air outlet
INSTALLATION

TECHNICAL FEATURES

MICRO 3 SE
AM 2-10 F1 Micro
10
bar 8 10
type MSC60
rpm 3180 2900 2900
290
l/min 325 290
l 2,2
l 0,25
kJ/h 7524
m3/h 880
mg/m3 4
type MEC 90/L
kW 2,2
3
kW 3 3
n° 10
°C +2/+45
58
V/Hz 400/50-60
V/Hz 230/50-60
Amp 35
5,2
Amp 5,2 5,2
IP 54
F
S1
°C 110
°C -
110
°C
Amp 5,5
bar 14
mm 580
mm 480
mm 760
kg 87
BSP ½"
MICRO 4 SE MICRO 5 SE
AM 3-10 F1 Micro
10
8 10 8 10
MSC60 MSC60
3750
3940 3750 4960 4460
385
430 385 580 485
2,2 2,2
0,25 0,25
10260 13680
880 880
4 4
MEC 100/LA MEC 100/LC
3 4
4,2
3,8 4,2 4,8 4,8
10 10
+2/+45 +2/+45
60 60
400/50-60 400/50-60
230/50-60 230/50-60
40 52
6,6
6,2 6,6 8,7 8,4
54 54
F F
S1 S1
110 110
- -
110 110
6,6 8,8
14 14
580 580
480 480
760 760
92 93
½" ½"
Rotar Micro - Cod.197CC2300 - Rev.01 - 07/2008
GB
3
MICRO 5 TA
8 10 13
MSC60
4960 4460 3750
580 485 350
2,2
0,25
13680
880
4
MEC 100/LC
4
5 5 5
10
+2/+45
60
400/50-60
6-12-24/50-60
24
8,7 8,7 8,7
54
F
S1
110
105
110
5,2
14
580
480
760
94
½"
7 7 7 7 7