Use Of The Battery Charger; Battery Life - Pressfit PUMA-RR Manual De Uso

PUMA-RR and LYNX-RR only: during the pressing cycle, force and pressure
values are shown instantly on the display. After the motor switches off, the
display shows "OK" to indicate the cycle has been completed successfully,
the tool has reached the calibrated pressure and the nominal pressing force.
The message "ERROR" accompanied by a warning sound and fl ashing
LEDs indicates an error in the pressing procedure; the operation has been
interrupted without reaching the calibrated pressure and force values; in
this case, pressing must be repeated by holding down the power button.
In case of emergency, the pressing cycle can be interrupted
at any time by pressing the release button (7) to return
the ram to the start position and allow the jaws to be opened.
The tool is not suitable for continuous use; adequate
breaks must be taken to allow the tool to cool down.
3.4) Opening the jaws
After the motor has switched off automatically:
Release the power button; the ram will return automatically to the start
position (SMART RELEASE) (Fig. n).
Open the jaws by hand by pressing at the rear top and bottom then
remove the tool from the pressed joint (Fig. o)

3.5) Battery life

The battery is fi tted with LEDs that show the battery life remaining at any
time when the button is pressed (Fig. e):
4 LEDs: full battery
2 LEDs: 50 % battery
1 LED fl ashing: low battery, recharge the battery.
PUMA-RR and LYNX-RR only:
the battery life can also be checked
using the touch button (see part 4).
If there is too little charge, a warning is shown on the
display when the power button (2) is pressed;
the battery must be recharged.
In this situation, the tool will not start.
PUMA and LYNX only: If there is too little charge, the LEDs will light
up accompanied by a long warning sound when the power button (2) is
pressed; the battery must be recharged for use.
In this situation, the tool will not start.
NOTE: when there is too little charge, an electronic safety lock pre-
vents the voltage from dropping below the minimum safety level, to
safeguard the battery from damage caused by excessive discharge.
After every work cycle and after the battery has been removed from the
tool, an electronic device automatically switches off the battery; this is
confi rmed by the fl ash of the LED adjacent to the power button.
The battery switches back on when it is reinserted into the tool and the
power button is pressed.
GB
max. min.
BATTERY BATTERY
BATTERY

3.6) Use of the battery charger

Follow the battery charger instructions carefully, referring to mod.
ASC30-36.
The average time required to fully recharge the battery is 40 min.
Recharge the battery using only the charger provided.
4. OLED DISPLAY (PUMA-RR and LYNX-RR only)
The –RR versions are fi tted with an OLED display (5) that is activated upon
tool start-up and switched off automatically after approx. 60 s not in use;
it displays the operating parameters and any alarms and failure warnings.
The capacitive touch button (6) allows you to browse the settings of the
"main menu".
4.1) Example of "main menu" settings
F = 32.0 kN
Fm: Minimum guaranteed force, expressed in kN.
m
*
F = 0 kN
Fp: Instantaneous force achieved expressed in kN.
p
(standard factory display setting)
F = 3.60 ton
m Fm: Minimum guaranteed force, expressed short ton (USA).
*
F = 0 ton
Fp: Instantaneous force achieved expressed in short ton (USA).
p
P = 708 bar
Pm: Minimum guaranteed pressure expressed in bar.
m
*
P = 0 bar
p Pp: Instantaneous pressure expressed in bar.
P = 10269 psi
Pm: Minimum guaranteed pressure expressed in psi.
m
*
P = 0 psi
p
Pp: Instantaneous pressure expressed in psi.
*
Battery charge level.
BATTERY
No. of cycles performed.
0
*
No. of cycles before scheduled recommended maintenance.
-30000
tool model
PUMA-RR
*
tool serial number.
NR17RP682
LED LED
OFF
ON
RESET Return to original factory settings.
SW:S1J78409
Firmware version (see part 4.5).
*
these settings can be set as the "main screen" which is shown on the display at every use
of the tool; to do this, when the pre-selected screen is displayed, hold the fi nger on button
(6) until a confi rmation "beep" is heard.
Never poke or push down hard on the touch button;
touch it gently with a bare fi nger.
8
Enabling/disabling the LED Worklights.
(see part 4.2).