Stove Status Menu 05; Working Hours Menu 06; See Calibration Menu 04; Chrono Setting Menu 02 - Elledi RODI STEEL Manual De Uso Y Mantenimiento

5. By confirming with the P6 key, you will automatically go back to SELECT LANGUAGE MENU 03.
The availability of languages may change according to the type of FIRMWARE version.

STOVE STATUS MENU 05

In this menu, you can check the most important components of the pellet thermo-stove for proper operation and for the presence of values
typical for this condition.
To enter this menu, follow the steps below starting from the main menu status:
1. Press and hold the P4 key for 2 seconds until the CLOCK SETTING MENU appears.
2. Press the P4 key four times: the display will show STOVE STATUS MENU.
3. Access via the P6 key: the display shows the desired screen.
4. Pressing the P3 key automatically brings you back to the STOVE STATUS MENU 05.
This menu is used both by the Technical Support Centre to understand the reasons for the thermo-stove malfunctioning,
and by private users when pellets are loaded into the hopper.
MOTOR ROTATIONS

WORKING HOURS MENU 06

The total working hours of the thermo-stove are recorded in the WORKING HOURS menu. In some cases, working hours may not
be reset, that is, numbers similar to 5000/15000/25000 may be displayed. The technician is responsible for resetting these numbers
at switch-on. This does not mean that the thermo-stove has already operated for all those hours; it is just a programming setting
performed during Elledi's first test before stoves are packed and dispatched.
To enter this menu, follow the steps below starting from the main menu status:
1. Press and hold the P4 key for 2 seconds until the CLOCK SETTING MENU appears.
2. Press the P4 key five times: the display will show WORKING HOURS MENU.
3. Access via the P6 key: the display shows the desired screen.
4. By confirming with the P6 key, you will automatically go back to WORKING HOURS MENU 06.

SEE CALIBRATION MENU 04

In this menu you can see the values of the parameters set in the control unit.
This menu is used by the Technical Support Centre to understand what the parameters set in the machine are, and then identify the
changes useful to improve thermo-stove operation.
To enter this menu, follow the steps below starting from the main menu status:
1. Press and hold the P4 key for 2 seconds until the CLOCK SETTING MENU appears.
2. Press the P4 key three times: the display will show SEE CALIBRATION MENU 04.
3. Access via the P6 key: the display shows the desired screen.
4. Scroll with the P6 or P7 key to display the set parameters.
5. By scrolling to the last parameter you will automatically go back to SEE CALIBRATION MENU 04.

CHRONO SETTING MENU 02

With the chronothermostat function switching on and off the thermo-stove in two independent time intervals (PROGRAM 1 and
PROGRAM 2) can be programmed for each day of the week.
To enter this menu, follow the steps below starting from the main menu status:
1. Press and hold the P4 key for 2 seconds until the CLOCK SETTING MENU appears.
2. Press the P4 key five times: the display will show CHRONO SETTING MENU 02.
3. Access via the P6 key: the display shows the desired screen.
10:00
START
PROG - 1
Model Rodi Steel Use and Maintenance Manual
2000
130°C 1.5b
FEED SCREW 0
STATUS 1
SMOKE TEMPERATURE
THERMO-STOVE STATUS
If this black segment is not lit on the display close to the clock symbol, you can still
do the programming. To enable this function, refer to the current day setting section,
(7.1.2 CLOCK SETTING MENU 01) as the value must be different from OFF.
Rev.2 31/07/2017
Page63
WATER PRESSURE
FEED SCREW STATUS