Dealer Service And Adjustment; Dealer Service Introduction; Critical Maintenance Tips; C.CLeaning - Quickie Q7 Manual De Instrucciones

E NG LIS H
The owner of this chair is responsible for makiing sure that it has been setup and adjusted by a trained service
professional under the advice of a healthcare advisor. Service and/or adjustments should only be done with the
advice of a healthcare professional. Always use parts and/or accessories that have been recommended and
approved by Sunrise Medical when servicing this chair.
A. DEALER SERVICE INTRODUCTION
1. Once per year, this chair needs a complete inspection, safety check, and regular service made by an
authorized dealer.
2. A torque setting is right force used to tighten a particular fastener. Proper torque settings must be used
where specified. When not specified, torque settings should be 60 in-lbs
3. If you have discovered a worn, bent, or damaged part, repair or replace them with recommended parts
before returning this chair to service.
4. All major maintenance and repair work should be done by the authorized dealer.
B. CRITICAL MAINTENANCE TIPS
1. Torque settings:
A torque setting is the optimum tightening which should be made on a particular fastener. It is important to use
proper torque settings where specified. When not specified, torque settings should be 60 in-lbs
2. Dealer Service and Adjustment Reference materials:
Go to www.sunrisemedical.com for parts manuals, instruction sheets, and instructional videos that will aid in the
repair of the Quickie 2 Family of wheelchairs.
C. CLEANING
1. Paint Finish
a. Clean the painted surfaces with mild soap or detergent.
b. Protect the paint with a coat of non-abrasive auto wax.
2. Axles and Moving Parts
a. Clean around axles and moving parts with a slightly damp (not wet) cloth.
b. Wipe off or blow away any fluff, dust or dirt on axles or moving parts.
c. DO NOT USE 3 in 1 oil, or WD-40 ® for lubrication. Only use Teflon based Lubricant when working on
this wheelchair.
D. REAR WHEEL AXLE NUT ADJUSTMENT
The rear wheel axle (B) attaches the rear wheel (D) to the camber plug (C). When the detent balls (E) engage
into the camber plug the rear wheel effectively becomes locked onto the chair. Pushing the quick-release button
(A) disengages the detent balls and allows removal of the axle and wheel assembly.
To adjust the axle you will need a 3/4" wrench to turn the adjustment nut (F). You will also need a 1/2" wrench
to securely hold the ball detent end of the axle to prevent it from turning.
If the wheel and axle will not lock into the camber plug then the axle requires adjustment. Turn the nut counter-
clockwise approximately 1/4 revolution and try to lock the axle into the camber plug. If it doesn't lock, continue
making small nut adjustments until it securely locks.
If the wheel is locked on the chair but there is excessive wheel play (the wheel hub can be pushed back and
forth on the axle) then adjust the nut clockwise until there is no perceptible gap between the wheel and camber
tube and the axle is securely locked onto the chair.
21 22
E. WHEEL LOCKS
Quickie Q7 Adjustable and Quickie Q7 Active Rigid wheelchairs are shipped with one of
five types of wheel locks. Wheel locks are installed at the factory unless you have requested other-
wise.
Use a torque setting of 62 in.-lbs. (7 Nm) when setting up wheel locks.
1. High-Mount Push-to-Lock or Pull-to-Lock Wheel Locks Adjustment
a. Using a 4mm Allen wrench, turn one of the screws (G) in the clamp counterclockwise one-
quarter turn.
b. Repeat the same process with the remaining screw (G).
c. Alternately loosen the screws (two turns each) until both screws are loose.
d. Slide clamp toward the rear wheel until the wheel lock is embedded into the tire to prevent
wheel movement, when in the locked position.
e. Tighten screws to 62 in-lbs. (7 Nm).
112786 Rev. F
WARNING
19 20
21
18
IX. DEALER SERVICE AND ADJUSTMENT
TOOLS YOU WILL NEED
1. Imperial Hex key set
2. Metric Hex key set
3. Imperial Open-end Wrench set
4. Metric Open-end Wrench set
5. Torque wrench
6. Imperial Hex bit Socket set
7. Metric Hex bit Socket set
8. Phillips and Flat screwdrivers
E
G
19
E
F
20
21