Troubleshooting, Specifications; Inspection And Maintenance - Maglite Mag Charger RE1019 Manual Del Propietário

Troubleshooting
Section 7
If you have questions or need assistance, please call our warranty/repair
facility at 01 (909) 947-1006.
Problem Cause/Correction
Flashlight:
Does not light 1. Tighten tail cap – make sure unplated area of tail cap and barrel
are clean.
2. Check if battery is installed ... see page 9.
3. Check if battery is installed with (+) positive end toward head of
flashlight.
4. Make sure large end of battery spring is snapped into tailcap.
Battery charged? 1. Check battery charge: Place flashlight in recharger/cradle. Make
sure LED lights up with flashlight switch off (see page 9). Charge
for 15 minutes ... check for light. If it lights (even momentarily)
charge it, if not, replace it (battery).
Switch sticks 1. Return flashlight to Mag Instrument (see warranty).
Works intermittently 1. Check for damage to battery casing.
2. Foreign particles inside barrel.
3. Lamp not seated properly.
Poor or no spot 1. Lamp needs centering (see page 12).
2. Damaged lamp (filament off-center) — replace.
Recharger/Cradle:
LED indicator does 1. Tighten tail cap.
not light when 2. Check plug connection to converter.
flashlight switch is 3. Check plug to power source.
in off position. 4. Make sure large end of battery spring is snapped into tailcap.

Inspection and Maintenance

Battery Pack – See Warnings Section for more information. Periodically (approximately
every month) remove the battery pack from the flashlight and visually inspect for signs
of gas or chemical leakage. Indications of leakage are discoloration of the plastic sleeve
or white fuzzy material near the top (positive side button) of each cell.
indication would be a bulging deformation of the bottom (negative flat end) of the cell
can. If these signs are observed the battery pack should be removed from service to
prevent chemical damage to the inside of the flashlight. See One Year Battery Pack
Warranty for more information concerning warranty coverage.
Fully Charged Battery Storage – If you do not use your flashlight for long periods of
time (four months or more) we suggest you remove the battery pack from the flashlight
to prevent chemical damage (acid leaks). Electrical Contacts – The bare (bright) metal
surfaces between the tailcap and barrel must be cleaned periodically to ensure a good
electrical contact. lso keep the tailcap spring clean. O-ring Seals and Screw Threads –
To keep seals from drying out and the threads operating smoothly, apply several drops
of clean petroleum oil or jelly to these surfaces two or three times a year.
Exterior Finish – The protective finish on the flashlight is very durable; however,
constant exposure to sunlight, water, chemicals, gases, etc., will dull, discolor and
eventually destroy the protective finish. Care should be taken to avoid any harsh
environment.
14
Specifications and
Flashlight
• Tempered aluminum alloy external
components
• Finish: hard, type III, aircraft
anodized (inside and out)
• Length: 12-19/32" (319.79 mm)
• Weight, with battery pack: 32 oz.
(907.18 grams)
• Weight, without battery pack:
18 oz.(510.29 grams)
• Head diameter: 2-5/16" (58.72 mm)
• Barrel diameter: 1-9/16" (39.67 mm)
• Permanently engraved serial
number for registration and
identification
• O-ring sealed throughout
• High intensity halogen lamp (50*
hour rating) Easy replaceable lamp
12 Volt dapter ( utomobile)
Plug the DC power cord's adapter into the 12–14
volt cigarette lighter receptacle of the vehicle. DO
NOT leave adapter plugged in for any extended
period while the engine is "off" to avoid draining
nother
vehicle battery.
230-Volt Converter
fter mounting the Charging Cradle in a
proper location, plug the special matching electrical
connectors together at the wire ends of the Cradle and
Converter. Plug the Converter into an appropriate 230 volt
wall receptacle.
nodized
Note: Total usable wire length is 8 feet.
*Lamp life may vary.
ccessories
• 6.00 Volt NiMH Battery Pack • Charge rate: 230 m continuous
• High-Quality Tempered Glass Lens • Flashlight can be charged in any
• Highly-polished, scientifically- position
designed, metallic reflector • Reverse voltage protected
withstands extreme temperatures (batteries in backwards) Input and
• Diamond knurl design Output
• Cam-action adjustable beam from • Red light emitting diode (LED)
spot to flood with 1/4 turn of head charge indicator
• Corrosion resistant metal • Mounts in any position
springs throughout • Includes (2) detachable mounting
• Spare Halogen lamp included in bracket
tailcap
Converter
Charging Cradle • Input 230 volts C 60Hz
• ccepts 12–14 volts DC • Output 12 volts DC
(not for use with 24-volt systems) • Double insulated
• Constant current solid-state
integrated circuit regulator