Instructions D'iNstallation Pour L'aMpli Sg-Da82000 Signature Series - Fusion Signature Serie Instrucciones De Instalación

Storage temperature range From -20 to 70°C (from -4 to 158°F)
Water rating Must be installed in a dry location
Weight 5.2 kg (11.5 lb) with the cover installed
Dimensions
9
420 mm (16 / in.)
16
1
388 mm (15 / in.)
4
5
160 mm (6 / in.)
16
9
210 mm (8 / in.)
32
3
5 mm ( / in.)
16
1
56.6 mm (2 / in.)
4
More Information
Registering Your SG-DA82000 Signature Series
Help us better support you by completing our online registration today.
• Go to www.fusionentertainment.com.
• Keep the original sales receipt, or a photocopy, in a safe place.
Troubleshooting
Before you contact your FUSION dealer or service center, you should perform
a few simple troubleshooting steps to help diagnose the problem.
If the FUSION amplifier has been installed by a professional installation
company, you should contact the company so a technician can assess the
problem and advise you about possible solutions.
There is no sound, and the POWER LEDs are off
• Check the amplifier turn-on wire connection to the stereo or switch, and
tighten or re-connect all wires, if needed (Connecting to Power, page 3).
NOTE: The amplifier and the stereo must connect to a common ground for
the amplifier turn-on signal to function properly.
• Check the fuse or circuit breaker on the power cable (near the battery),
and replace the fuse or reset the breaker, if needed.
• Check the fuses on the amplifier, and replace all blown fuses, if needed.
• Check the power and ground cable connections, and tighten or re-connect
all cables, if needed.
• Make sure you are using the appropriate gauge for the length of the power
cable run, and replace the cable with a thicker gauge, if needed (Power
Cable Gauge Guide, page 3).
There is no sound, and the POWER LEDs are on
• Check the settings on the stereo, and make sure the appropriate zone out
or subwoofer out signals are enabled.
NOTE: See your stereo owner's manual for more information on enabling
or configuring output signals.
• Make sure the stereo is powered on and the volume is not set too low.
• Check the RCA cable connections to the stereo, and re-connect all
disconnected cables, if needed.
• Check the LEVEL setting for the zone on the amplifier and the max volume
setting for the zone on the stereo, and increase the LEVEL on the amplifier
6
or the max volume on the stereo, if needed (Adjusting the Level for a Zone,
page 5).
• Check the speaker wire connections, and re-connect all disconnected
wires, if needed.
• Check the power cables to make sure they are the appropriate gauge, are
fused, and are connected properly (Connecting to Power, page 3).
One POWER LED is on, but the other POWER LED is off
• Check the fuses on the side of the amplifier where the POWER LED is off,
and replace all blown fuses.
The PROT LEDs are on
The PROT LEDs indicate a fault in the system. When a fault is detected, the
amplifier shuts down to prevent damage.
• Check the power and ground cables for cuts in the sleeving or bare wire
contact, and correct, repair, or replace the cables if necessary.
• Check the speaker wires for cuts in the sleeving or bare wire contact, and
correct, repair, or replace the cables if necessary.
• Check the temperature of the amplifier, and if the amplifier is very hot,
move it to an area with better ventilation or install a ventilation fan
(Mounting Considerations, page 2).
There is a hum or other unexpected noise from a speaker
• Install ground-loop isolators inline with the RCA cables from the stereo.
NOTE: You should install ground-loop isolators on all RCA cables
connected to the stereo.
You should install ground-loop isolators on the RCA cables where they
connect to the stereo, not where they connect to the amplifier.
The sound is distorted or clipping
• Check the output from the stereo, and adjust the zone line out to
3
approximately / volume if needed.
4
• Adjust the LEVEL setting on the amplifier for the zone or zones
experiencing distortion or clipping until the issue is corrected.
NOTE: The level setting depends upon the type of music and not all levels
are appropriate for all types of music. For example, if you adjust the level
setting for rock music, then listen to classical music, you could experience
distortion due to clipping.
物質宣言
部件名称 有毒有害物质或元素
铅 汞 镉 六价铬
电路版
O O O O
框体
O O O O
附件
O O O O
本表格依据 SJ/T11364 的规定编制。
O: 代表此种部件的所有均质材料中所含的该种有害物质均低于
(GB/T26572) 规定的限量
X: 代表此种部件所用的均质材料中, 至少有一类材料其所含的有害
物质高于
(GB/T26572) 规定的限量
*該產品說明書應提供在環保使用期限和特殊標記的部分詳細講解
產品的擔保使用條件。
Instructions d'installation pour l'ampli SG-
DA82000 Signature Series
Informations importantes relatives à la sécurité
AVERTISSEMENT
Consultez le guide Informations importantes sur le produit et la sécurité inclus
dans l'emballage du produit pour prendre connaissance des avertissements et
autres informations importantes sur le produit.
AVERTISSEMENT
Cet appareil doit être installé conformément à ces instructions.
多溴联苯 多溴二苯醚
O O
O O
O O
產
品
Instructions d'installation