Publicidad
Idiomas disponibles
Idiomas disponibles
l_[=]]_S]g
I Installing
the FM
indoor
antenna
]
T_ne in an FM station (see page 15), set the antenna
in a position
n which distortion
and noise is
rnmirnum, then fasten the tip of the antenna in this
position
using tape or a pin
FM ndoor anten/a
IConnecting
an FM outdoor
antenna
]
If broadcasts
cannot be tuned in clearly with the
included antennar use an outdoor
FM antenna,
connect 8 converter adapter to the coaxial cable and
connect the converter
adapter to the set's FM COAX
(75 _Z/uhms) terminal
Selecting
a place
for the FM
outdoor
antenna
• Set the antenna so that t is pointing towards
the
broadcast station's transmitting
antenna
• Behind buildings
or mountains,
set the antenna
in
the position
at which reception
is bestr and also try
changing the direction
of the antenna
• Do not install the antenna
undeE poweE lines
Doing so is extremely
dangerous,
as the power line
could touch the antenna
• hstafl the antenna away from roads or tracks to
avoid noise from cars or trains
• Do not install the antenna too high, as it may be hit
by lightning
Note to CATV system installer:
This reminder
is provided to Call the CATV
system installer's attention to Article 820-40 of
the NEC which provides guide lines for proper
grounding
and, in particular, specifies that the
cable ground shaft be connected
to the grounding
system of the building,
as close to the point of
cable entry as practical
I Installing
the AM
loop
antenna
I
T_ne in an AM station
(see page 15), set the antenna
in a position
as far from the system as position n
which distortion
and noise is minimum
In some
cases it is best to invert the polarities
AM broadcasts
cannot be received
well f the loop antenna is not
connected
or if it is set close to metal objects
IAssembling
the AM
loop
antenna
Assemble
the included AM loop antenna
as shown in
the diagram
IConnecting
the AM
loop
antenna
I
Connect the included AM loop antenna to the
antenna terminals
as shown in the diagram
_1 Lower
_2}Insert the
,_3- Return the
the lever
antenna wire
lever
I Installing
an AM
outdoor
antenna
I
Connect the signal wire from the AM outdoor
antenna to the antenna terminal
(ANTENNA
AM)
Be sure to ground the antenna and connect the
ground wire to the GND terminal
Also be sure to
connect the included AM loop antenna
I Mounting
on a wall
]
• The D-107 arid speakers (USC-107)carsbe mounted on a wall
1
Connect
the system
cable
to the
bottom
of the D-107.
(See
page
7.)
There is no need to mount the stand
2
Connect
the cords
to the speakers,
(See
page
7,}
There is no need to mount the stand
3
Mount
the D-107
and
speakers
to the
wall
using
commercially
available
screws
and the holes
on the rear
panels
of the D-107
and speakers.
When mounting
the screws
on the wall,
for convenience
the included template
can
be used to determine
the positions
of the
screws beforehand
Select screws
referring to B_e diagram
below
[Wall mount
hole on rear panel of main
unit and speakers]
42 mm
_
_
0 r,/m
4
Use the holes on the rear panels of
the D-107 and the speakers to mount
the D-107 and the speakers onto the
screws in the wall.
5
Connect the system cable and
speaker cords to the subwoofer,
(See page 7.}
NOTES:
• When mounting
on the wall, take care that no
accidents
occur due to the D-107 or speakers
falling
• Check the wall surface before mounting
the D-
107 and speakers to make sure it s strong
enough to support the weight
• Consult a specialist
if you do not know how
strong the wail s
• Screws for mounting
the Dq07
on the wall are
not included
Use screws
suited to the strength
and material of the pillar or waft
• Fasten the speaker cords and system cables in
place so that theEe s no risk of them being
puffed accidentally,
cads ng the main unit or
speakers to fall
• Be sure to mount using screws for all four
screw holes on the CD receiver and both screw
holes on the speakers
If any of the screw
holes
are not used, the CD receiver or speakers will
be unstable and risk failing
• Do not install the CD receiver too high up If the
CD receiver is too high, the remote
control
signals may have not reach t easily, making it
difficult
to opeEate
• Note that Denon will not be held responsible
for
any accidents
or damage due to improper
assembly
or mounting,
nsufficient
mounting
strength,
erroneous
usage, natural disasters,
etc
AM outdoor
[]
PART NAMES,
FUNCTIONS
AND DISPLAYS
I(1} CD receiver
(D-107),
Speakers
(USC-1O7)
and Subwoofer
(USW-107}
]
Org gate
O
ON/STANDBY
button
Press to button
on the power and preos again
to set the standby mode
• The indicator
color changes as follows,
according to the condition:
When in the power on mode:
G_een
When in the standby mode:
Red
When in the timer standby mode:
Orange
When in standby in the eco-mode:
Light off
FUNCTION
button
• Press this to select the function
• The function changes
in the following
order
each time this button is pressed:
co
8
Publicidad
