Installation; Overall Dimensions; Positioning The Indoor Unit - Liebert HIROSS Hisp SE Serie Manual De Usuario/ Instalacion

Tab. 2 --- Sound pressure levels
Sound pressure levels, for measurement carried out with standard fan speed regulator (Variex).
Model Model
50Hz 50Hz
SE 04
SE 05
SE 06
Indoor, free field at 2 m in front of Indoor, free field at 2 m in front of
SE 08
the unit
SE 10
SE 13
SE 14
SC 04
SC 05
SC 06
Outdoor, free field at 2 m in front Outdoor, free field at 2 m in front
SC 08
of the unit of the unit
SC 10
SC 13
SC 14
Note: Values are referred to an ambient temperature of 35_ C.
Sound pressure levels, for measurement carried out with standard fan speed regulator (Variex).
Model Model
60Hz 60Hz
SE 04
SE 05
SE 06
Indoor, free field at 2 m in front of Indoor, free field at 2 m in front of
SE 08
the unit
SE 10
SE 14
SC 04
SC 05
SC 06
Outdoor, free field at 2 m in front Outdoor, free field at 2 m in front
of the unit of the unit of the unit
SC 08
SC 10
SC 14

2 --- Installation

CAUTION: the ambient unit must never be installed
outdoors.

2.1 --- Overall dimensions

See Fig. 1 and Fig. 2 for the overall dimensions of the
evaporating unit (SE) and of the external motor con-
densing unit (SC).
Fig. A --- Evaporating unit SE
English
Octave band frequency (Hz)
63 125 250 500
52 56 50 48
55 61 58 56
56 61 58 57
45 49 49 45
45 49 49 45
46 50 50 46
49 54 54 50
51 56 56 52
53 57 58 54
54 58 59 57
Octave band frequency (Hz)
63 125 250 500
53 57.5 57 53.5
60 61 56 54.5
63 60.5 57.5 59
43.5 47 51.5 46.5
47.5 51 55 50
49.5 53 57 52
57.5 62.5 57.5 54.5
53.5 58 61 57
54.5 59 64 61.5

2.2 --- Positioning the indoor unit

S Unpack the units as close to the place where it has
to be installed as possible. Once unpacked, avoid
stress any impact to its internal components.
S The air conditioner (indoor unit) can be installed
in any indoor location provided it is not exposed to
an aggressive ambient.
S Position the indoor unit next to the main heat
source.
S Fix the unit to the
ceiling or to the
wall by inserting 6
(SE 04--- 05--- 06)
or 8
08--- 10--- 13--- 14)
expansion
thorough clamps
(in this case en-
sure the clamp is
sealed) in the f8--- mm holes on the two side brack-
ets.
S Make sure the airflow circulate freely.
S To allow the servicing of the unit, the Service Area
showed in Fig. 5, has to be left unobstructed (in
Fig. 5c the 200--- mm minimum clearance from the
back of the evaporating unit is approximate. It has
to be left to ensure that the refrigerating lines can
be connected to the valves on the back panel).
2
Sound pressure level Sound pressure level
1000 2000 4000
51 49 46
54 52 51
55 52 51
41 38 36
41 38 36
42 39 37
46 43 40
48 45 43
51 47 43
53 49 45
Sound pressure level Sound pressure level
1000 2000 4000
49.5 47 44.5
56 54.5 52
60 59 56
43 39.5 36
47.5 44 40
49.5 46 42
50 49 44
52 50.5 46
57.5 53 48.5
(SE
or
Fig. B --- Detail of the clamp
[dB(A)] [dB(A)]
55
60
62
47
47
48
52
54
56
58
[dB(A)] [dB(A)]
56
61
65
49
53
55
57
59
63