Serial Connection Parameters; Read-Only Parameters - Carel HumiSonic Manual Del Usuario

ENG
b0 1. Unit of measure 2. Enable backup function
for parameter b1
M = minutes; H =
hours
193 H
194 H
195 H
196 H
197 H
198 H
199 H
200 H
201 H
202 H
203 H
204 H
205 H
206 H
207 H
208 H
209 H
210 H
211 H
212 H
213 H
214 H
215 H
216 H
217 H
218 H
219 H
220 H
221 H
222 H
223 H
224 H
225 H
226 H
227 H
228 H
229 H
230 H
231 H
232 H
233 H
234 H
235 H
236 H
237 H
238 H
239 H
240 H
241 H
242 H
243 H
244 H
245 H
246 H
247 H
248 H
249 H
250 H
251 H
252 H
253 H
254 H
255 H

9.3 Serial connection parameters

Parameter
C1 Baud rate: 0 = 4800 bps; 1 = 9600 bps; 2 = 19200 bps; 3 = 38400 bps
C2 tLAN address (if 0 = Main)
C3 Serial address
C4 Timeout for Main serial offline alarm

9.4 Read-only parameters

Parameter
d0 TH probe temperature reading
d1 TH probe humidity reading
d2 Configurable input reading (optional card)
d3 Tank operating hour counter (resettable, see 7.8)
d4 Unit hour counter (read-only)
d5 Instant production
d6 Time remaining to end of piezoelectric transducer life
d7 Manage Secondary unit production
d8 Dew point
(*) after 999 the display shows to indicate the 1000s (the three digits are displayed with a dot at the top between the first and second digit).
Direct version for room applic. +0300062EE - rel. 1.4 - 24.09.2020
3. Drain solenoid 4. Alarm relay activation
valve in standby AL= alarms present
SP= set point reached
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Open
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
ON Closed
5. Alarm relay logic 6. Enable wash
NO= norm. open due to inactivity
NC= norm. closed
AL NO
AL NO
AL NO
AL NO
AL NO
AL NO
AL NO
AL NC
AL NC
AL NC
AL NC
AL NC
AL NC
AL NC
AL NC
SP NO
SP NO
SP NO
SP NO
SP NO
SP NO
SP NO
SP NO
SP NC
SP NC
SP NC
SP NC
SP NC
SP NC
SP NC
SP NC
AL NO
AL NO
AL NO
AL NO
AL NO
AL NO
AL NO
AL NO
AL NC
AL NC
AL NC
AL NC
AL NC
AL NC
AL NC
AL NC
SP NO
SP NO
SP NO
SP NO
SP NO
SP NO
SP NO
SP NO
SP NC
SP NC
SP NC
SP NC
SP NC
SP NC
SP NC
SP NC
UoM range def
- 0 to 3 2
- 1 to 207 1
s 0 to 240 30
UOM range def
°C/°F 0-1000 0
%rH 0-1000 0
% / %rH 0-100 0
h 0-9999(*) 0
h 0-9999(*) 0
kg/h 0 to 8 0
(lb/h) 0 to 17.6
h 0 to 9999
9999(*)
- 0-1 0
°C/°F 0 to 1000 0
22
7. Off = wash due to inactivity at
next start
On= standard wash due to
inactivity
Off Off
On Off
On Off
Off On
Off On
On On
On On
Off Off
Off Off
On Off
On Off
Off On
Off On
On On
On On
Off Off
Off Off
On Off
On Off
Off On
Off On
On On
On On
Off Off
Off Off
On Off
On Off
Off On
Off On
On On
On On
Off Off
Off Off
On Off
On Off
Off On
Off On
On On
On On
Off Off
Off Off
On Off
On Off
Off On
Off On
On On
On On
Off Off
Off Off
On Off
On Off
Off On
Off On
On On
On On
Off Off
Off Off
On Off
On Off
Off On
Off On
On On
On On
note
The alarm is only generated if network production
control is active (see the corresponding chapter)
note
equal to AF - piezoelectric transducer hour counter
R/W parameter: 0 = the Secondary unit exactly replicates
the production of the Main unit, as it depends on the
setting of parameter P0 on the Main unit;
1 = the Secondary unit produces according to the
request sent by the Main unit and its own P0 setting; it is
not affected by the setting of P0 on the Main unit
calculated using d0 and d1
8. Autotest
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Tab. 9.c
Tab. 9.d
Tab. 9.e