Installation Instructions; Appliance Description - BERTO'S MACROS 700 Serie Manual De Instrucciones

Cocinas a inducción
Ocultar thumbs Ver también para MACROS 700 Serie:
Tabla de contenido

Publicidad

58 |
ATTENTION!
Please refer to the initial pages of this manual for the figures mentioned in this chapter.

APPLIANCE DESCRIPTION

Sturdy stainless steel structure with 4 legs (adjustable in
height). Cooking tops in glass ceramic induction plates.
Control knobs made in synthetic material.
Legal and technical requisites
The manufacturer declares that the appliances are made
EN
in conformity with the EEC directives and requires that
the installation is performed in accordance with the
regulations in force.
During the assembly, the following requisites should be
adhered to:
- building regulations and local fire prevention provisions
- health and safety regulations
- current CEI regulations
- current Fire Brigade regulations
Handling and transportation
The units are placed on wooden pallets to facilitate
transportation and handling by a forklift or trolley either
on the premises or when they are loaded and unloaded.
Units are packed in 3-layer sturdy cardboard boxes with
stickers and prints applied onto them for providing advice
relevant to handling. The symbols give information about
their handling, forbid the lifting the units with hooks and
storing outdoors.
It also warns operators that the packaging contains fragile
objects and indicates the vertical position that the box
must keep. It also directs the operator on opening the
packaging from downwards to upwards.
Before beginning the installation, remove the packaging.
A few parts are protected with an adhesive film, which
should be removed carefully.
Remove any glue residual with the proper substances,
such as petrol; never use abrasive substances.
The unit must be leveled; small differences of height can
be solved by adjusting the legs. The main switch or the
socket must be close to the unit and easy to reach.
We recommend placing the unit under a suction hood so
that vapor can quickly evacuate.
Room ventilation
The room where the appliance is installed must be fitted
with air intakes to guarantee the correct operation of the
MOD.
Qn
V
INSTALLATION

INSTALLATION INSTRUCTIONS

N°:
kW:
Hz: 50/60
unit and air exchange. The air intakes must be of adequate
dimensions, be protected by grids and be positioned free
of any obstruction. (See Fig. 2 – Fig. 3).
Caution - Warning
Do not install the appliance near any other units
that can reach high temperatures: the electrical
components might be damaged. During installation,
make sure that the air suction and the means of
evacuation are free of any obstacles.
The installation, start-up and maintenance of the unit
must be performed by qualified personnel. All installation
operations must be carried out in conformity with
the regulations in force. The manufacturer declines all
liabilities in the event that the unit works incorrectly
because of an incorrect installation or because it does not
comply with the regulations in force.
The installation of the models with a side terminal board
must be carried out while keeping the unit 5 cm from the
back wall and 50 cm from the side walls. In models with a
back terminal board, the installation must be carried out
while keeping the unit 50 cm from the back wall and 50
cm from the side walls.
"In any case the unit must be installed/fixed in order it
is possible to replace the power supply cable after the
unit is installed".
WARNING:
If the following models:
E7P2M/IND - SE7P2M/IND - SE7P2PM/IND - SE7P2M/
IND-BF - SE7P2PM/IND-BF - E7WOK/IND - E9P2M/IND -
E9WOK/IND - SE9P2M/IND - SE9P2M/IND-BF - SE9WOK/
IND - SE9WOK/IND-BF - SE9TP2M/IND - SE9TP2M/IND-
BF - SE9TP2M/IND-BF
are installed as a single unit (not in a row), fix the anti-
tilt bracket to the floor by using the proper anchor screws
(see Fig. 1a); consider the minimum installation distances
described above. The free-standing appliances that weigh
less than 40 kg, must be fixed to the surface where they
IPX
INSTALLATION

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido