Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Roof Venting
Wall Venting
A
B
B
A. Roof cap
A.Wall cap
B. 6" (15.2 cm)
B. 6" (15.2 cm)
round vent
round vent
Installation Instructions
Prepare Location
• It is recommended that the vent system be installed
before hood is installed.
• Before making cutouts, make sure there is proper
clearance within the ceiling or wall for exhaust vent.
• Check your ceiling height and the hood height maximum
before you select your hood.
1. Disconnect power.
2. Determine which venting method to use: roof, wall, or
nonvented.
3. Select a flat surface for assembling the range hood.
Place covering over that surface.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING
4. Using 2 or more people, lift range hood onto covered
surface.
Range hood mountig screws installation
1. Determine and mark the centerline on the wall where the
canopy hood will be installed. Disconnect power.
2. Select a mounting height between a minimum of 24"
(61.0 cm) for an electric cooking surface, a minimum of
27" (68.6 cm) for a gas cooking surface, and a suggested
maximum of 36" (91.4 cm) above the range to the bottom
of the hood. Mark a reference line on the wall.
3. Tape template in place, aligning the template centerline
Non Vented
(recirculating)
A
B
A
A. Deflector
4. Mark centers of the fastener locations through the
B. 6" (15.2 cm)
round vent
IMPORTANT: All screws must be installed into wood. If there
is no wood to screw into, additional wall framing supports may
be required.
Remove the template.
5. Drill
6. Install the 2 - 5 x 45 mm mounting screws. Leave a
Vent cover bracket installation
7. Attach vent cover bracket to wall flush to the ceiling using
Complete Preparation
1. Determine and make all necessary cuts in the wall for the
2. Determine the required height for the home power supply
3. Run the home power supply cable according to the
NOTE: Do not reconnect power until installation is complete.
4. Use caulk to seal all openings.
8
and bottom of template with hood bottom line and with the
centerline marked on the wall.
D
R
L I
L
2
T (
W
O
)
3
1 /
6
"
P
L I
O
T
H
O
L
E
S
T
H
R
O
U
G
H
S
T
U
D
S
O
R
R
E
A
R
W
A
L
L
S
U
P
P
O
R
C
L
H
o
i r
o z
n
a t
l
L
n i
e
B
A. Centerline
B. Fastener locations
C. Mounting height reference (hood bottom line)
template to the wall.
⁄
" (4.8 mm) pilot holes at all locations where
3
16
screws are being installed into wood.
⁄
"(6.4 mm) gap between the wall and the back of the
1
4
screw head to slide range hood into place.
1⁄4"
(6.4 mm)
2 - 5 x 45 mm screws.
A
B
A. 8 x 40 mm drywall anchors
B. Centerline on wall
C. Vent cover support bracket
D. 5 x 45 mm screws
vent system. Install the vent system before installing the
hood. See "Venting Requirements" section.
cable and drill a 1¼" (3.2 cm) hole at this location.
National Electrical Code or CSA Standards and local
codes and ordinances. There must be enough ½" conduit
and wires from the fused disconnect (or circuit breaker)
box to make the connection in the hood's electrical
terminal box.
A
T
R
E
A
R
W
A
L
L
M
O
U
N
T
N I
G
T
E
M
P
L
A
T
E
A
L
G I
N
B
O
T
T
O
M
E
D
G
E
W
T I
H
P
E
N
C
L I
L
N I
E
N I
D
C I
A
T
N I
G
B
O
T
T
O
M
O
F
T
H
E
H
O
O
D
n I
s
a t
l
a l
t
o i
n
H
e
g i
h
t
C
C
D
Publicidad
Capítulos
Tabla de contenido
