Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
any part of the lower base when the handle
is lowered completely. Always do this with the
tool unplugged.
ADJUSTING THE STOPPER ARM (Fig. 3)
The lower limit position
of the blade can be easily
adjusted with the stopper
arm. Move the stopper
arm in the direction of
the arrow as shown in the
figure.
Adjust it to position A for full cutting. Adjust
the adjusting bolt so that the blade stops at
the desired position when lowering the handle
fully. Adjust it to position B, for dado cutting.
Adjust the adjusting bolt so that the blade
stops at the desired position when lowering
the handle.
ADJUSTING THE MITER ANGLE
Loosen the knob by turning counterclockwise.
When you have moved the knob to the posi-
tion where the pointer points to the desired
angle on the miter scale, tighten the knob
clockwise.
The height adjustable foot is to help keep
the tool in balance. After each miter angle
adjustment, you should turn knob on the foot
clockwise or counterclockwise until its bottom
touches the ground.
CAUTION: When turning the rotary table,
be sure to raise the handle fully. After chang-
ing the miter angle, always secure the rotary
table by tightening the knob firmly.
ADJUSTING THE BEVEL ANGLE
When tilting the carriage to the left, loosen the
lever at the rear of the tool counterclockwise.
Unlock the arm by pushing the handle some-
what strongly in the direction that you intend
to tilt the saw blade.
Tilt the carriage until the pointer points to the
desired angle on the bevel scale.
Then tighten the lever clockwise firmly to se-
cure the arm.
CAUTION: When tilting the carriage, be
sure to raise the handle fully. After changing
the bevel angle, always secure the arm by
tightening the lever clockwise.
Adjusting bolt
Stopper
Fig.3
arm
E N G L I S H •
SLIDE LOCK ADJUSTMENT
To unlock and lock the slide fence, turn the
lock knob counterclockwise or clockwise.
LASER
To turn on the laser
beam, press the upper
position (I) of the switch.
Press the lower position
(O) to turn off.
Laser line is factory adjusted so that it is posi-
tioned 1 mm from the side surface of the blade
(cutting position).
CAUTION: When not in use, be sure to turn
off the laser. Never look into the laser beam
directly; Laser beam may injure your eyes.
LASER RADIATION: DO NOT STARE INTO THE
BEAM or any CLASS II LASER PRODUCTS.
• CLEANING OF THE LENS FOR THE LASER LIGHT
If the lens for the laser light becomes dirty, or
sawdust adheres to it in such a way that the
laser line is no longer easily visible, unplug
the saw and clean the lens for the laser light
carefully with a damp, soft cloth. Do not use
solvents or any petroleumbased cleaners on
the lens.
NOTE: When laser line is dim and almost or
entirely invisible because of the direct sunlight
in the indoor or outdoor window near your
work area, relocate the work area to a place
not exposed to direct sunlight.
NOTE: All of the adjustments for the operation
of this machine have been carried out at the
factory.
CAUTION: Use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous radia-
tion exposure. The use of optical instruments
with this product will increase eye hazard. Do
not attempt to repair or disassemble the laser.
If unqualified persons attempt to repair this
laser product, serious injury may result. Any
repair required on this laser product should
be performed by authorized service center
personnel.
DUST BAG
The use of the dust bag makes cutting opera-
tions clean and dust collection easy. To attach
the dust bag, fit it onto the dust extraction
adapter.
U se r's m a n ua l
Fig.4
19
Publicidad
Tabla de contenido
