albatros MyTime Manual De Uso página 11

Instructions for operation
use the "+" and "–" keys to select the desired
setting.
The delicate Scottish shower adds a 5-second
burst of cool water every 30 seconds, and is
shown on the display as "L1".
The more intensive Scottish shower adds a 15-
second burst of cool water every 30 seconds, and
is shown on the display as "L2". You can switch
between these settings without interrupting the
current function.
To start the Scottish shower, simply press the
corresponding key once: to confi rm this selection,
the ring around the key and the LED will light,
and an acoustic alarm will sound. To switch off
the Scottish shower, press the corresponding
key twice after enabling the keyboard.
Multimedia (Top System version only)
The Multimedia feature allows you to listen to
your favourite music while using your MyTime
shower box.
Connect your external unit (battery-operated CD
or MP3 player etc.) to the 3.5mm external jack.
Never use mains audio appliances.
The volume can be adjusted from inside the
shower box by pressing the "+" and "–" keys; the
remaining functions (track selection etc.) must
be made on the unit itself.
Turkish Bath function
3
Congratulations on your choice – fi nally, a real,
programmable Turkish bath in your own home!
Before starting...
When using the Turkish bath function for the
fi rst few times, please remember that it is neces-
sary to acclimatize the body to sharp changes
in temperature and humidity. To do this, start
with short Turkish bath sessions and gradually
increase the times.
The temperature, too, should be increased only
gradually, as you become accustomed to the
humid heat of the Turkish bath alternated with
the cold water in the shower.
For the fi rst few Turkish baths, it is advisable to
limit the time to 10-15 minutes and the tempe-
rature to 40-45°. As you become accustomed
to these settings, slowly increase the duration
of the session to 20-25 minutes.
It is a good idea to take a full-body shower at the
end of the session in order obtain the maximum
benefi cial effect.
After taking a Turkish bath, it is advisable to relax
for a few minutes at room temperature.
And, having perspired heavily and therefore lost
mineral salts, it is very important to drink water,
infusions or fresh vegetable or fruit juice, which
are all rich in mineral salts and vitamins
Using the Turkish Bath
The Turkish bath function is factory-set to a
duration of 20 minutes and to the maximum
steam setting (level L3). If these settings are as
you prefer, then simply press the corresponding
key three times to start the function.
However, if you prefer to modify the Turkish bath
settings, you can easily select the desired time
and steam setting.
To do so, proceed as follows:
Uso box MyTime - Code 10009370 - Edition 3 - 12/2005
P
RE
To pre-select the Turkish bath function, press the
corresponding key once. The rings surrounding
the "STEAM", "+" and "–" keys will begin to fl ash;
modify the settings within three seconds.
S
ELECTING THE DURATION
You can select a duration of 20, 30, 40 or 180
minutes.
Press "+" or "–" until the desired duration is
displayed ("20", "30","40" or "∞" if 180 min. is
selected).
When you have entered the duration of your
Turkish Bath treatment, press the "STEAM" key
to confi rm the setting.
Setting the intensity of the steam
After modifying the duration, complete the pre-
selection procedure by setting the intensity of
the steam.
When the duration has been confi rmed, the rings
surrounding the "STEAM", "+" and "–" keys will
continue to fl ash; modify the intensity of the steam
as follows within 3 seconds.
The steam intensity is selected by pressing the
"+" and "–" keys, and is shown on the display as
"L1", "L2" and "L3".
- L1 light steam
- L2 medium steam
- L3 intensive steam
To confi rm the steam intensity selection, press
the "STEAM" key: the Turkish bath function will
start immediately.
The ring around the key and the LED will light,
and an acoustic alarm will sound.
To switch off the Turkish bath, press the cor-
responding key twice after enabling the key-
board.
Malfunctions
4
In the event of a malfunction, the keyboard
interrupts all the functions that are in operation,
switches off the radio and cancels all the settings
that you have entered. The display shows "E"
(fl ashing) followed by a numerical code which
identifi es the type of alarm condition that has
occurred.
N
O
If the display shows "E1", this means that the
vaporizer has not been fi lled with water.
Probable causes: Water supply shut off (lever "A"
or tap "B" closed, knob "C" turned to "keyboard"),
fault in the power supply unit.
N
O
If the display shows "E2", this means that the water
has not been heated to the correct temperature.
Probable causes: scale build-up inside the boiler
(carry out the de-scaling procedure); insuffi cient
water intake (or no intake); heating element or fi ll
solenoid faulty; mains water pressure too low.
N
O
This error code is displayed if steam is not ge-
nerated correctly during the vaporization phase.
Probable causes: insuffi cient water supply,
water supply interrupted, scale build-up inside
the boiler (carry out the de-scaling procedure);
heating element or fi ll solenoid faulty; mains water
pressure too low.
11
- T B
SELECTING THE URKISH ATH FUNCTION
W V
ATER IN APORIZER
W H
ATER EATING
S G
TEAM ENERATED
English