Publicidad
5. Analyse et Solution de Problèmes
5.1 Problèmes Causes et Solutions
Les Hacheurs ont été projetés pour que le minimum d' entretient soit
nécéssaire , toutes fois , quelques irrégularités dans leurs fonctionnement peuvent
se produire, suite à l' usage continu de l'equipement .
En cas de problème vérifier la Table No. 02 , où nous décrivons quelques
Table - 02
PROBLÈME
CAUSE
*
Le produit travaillé sort
* Un des composants internes de
écrasé .
la Tête de Hachage manque , ou
*
Courant électrique coupé
* La machine s'arréte pendant
le travail.
*
Problème dans les circuits
électriques internes ou externes
de la machine
* Engrenages usés ou cassés
*
Problème au moteur électrique
* Odeur de brulé ou fumée.
, ou d'autres parties électriques de
la machine
*
La machine démarre , mais les
* Condensateur de démarrage du
composant internes de la Tête de
moteur abimé.
Hachage , ne tournent pas tout de
suite .
* Composants internes de la Tête
* Bruits anormaux
de Hachage en mauvaise position
* Engrenages mal ajustés
* Fuites d' huile de la boite d'
*
Système d' étancheité
engrenages
defectueux
33
SOLUTIONS
* Verifier l' assemblage
conformement Figure 02.
.
*
Verifier si la fléche est dans
sa prise , ou s' il manque de l'
électricité
.
*
Appeler l' assistance
.
Téchnique
*
Appeler l' assistance
Téchnique
*
Appeler l' assistance
Téchnique
.
*
Appeler l' assistance
Téchnique
*Corriger la position des
composants internes comme
expliqué à la figure 02
*
Appeler l' assistance
Téchnique
*
*
Appeler l' assistance
Appeler l' assistance
Téchnique
Téchnique
1. Introduction
1.1 Safety
When not properly used the Meat Grinder Model PSEE- 09 can be potentially
DANGEROUS. Servicing, cleaning or any other operation shall be made by trained people.
The following instructions must be observed in order to avoid accidents:
1.1.1 Always unplug the machine when cleaning, servicing or when any other operation is
needed.
1.1.2 Never use tools that do not belong to the machine during operation.
1.1.3 Before switching the machine on check if the Head Nº01 (Pic.01) is firm in its position,
if all its internal components are assembled as well as if the Pan Nº04 (Pic.01) is mounted.
The machine does not start if the Pan is out of place.
1.1.4 Never spray water directly at the machine .
1.1.5 Never use loosen clothes specially shirts with loosen sleeves during operation.
1.1.6 Never put your fingers or any other object but the Stomper Nº05 (Pic.01) inside
feeding throat.
1.1.7 Keep hands off turning parts.
1.1.8 Never switch the machine on with wet clothes or wet shoes.
1.1.9 Before using the machine make sure it is properly grounded.
Your equipment is also protected against any eventual failure. Operator and motor's
integrity is maintained under this adverse condition. This protection is possible by means of
a thermal overload switch. In case your equipment suddenly stops wait for a few minutes
and press thermal overload switch button located at rear of machine.
This equipment shall not be used by persons (including children) having reduced
mental or physical capabilities, or having faulty experience or knowledge, unless they
have been previously supervised or instructed by a person responsible for the
equipment safety, about how to use it.
If the cord is not in good conditions to be used, it has to be changed by the manufacturer
or an Authorized Technical Assistant.
IMPORTANT
IMPORTANT
02
Publicidad
Capítulos
