Safety
DESCRIPTION
This Pedestal Sump Pump is designed for home
sumps. Unit is equipped with a 3-prong grounding-
type power cord. Sleeve bearings on motor shaft never
need lubrication. Automatic reset thermal protection.
NOTICE: This unit is not designed for applications
involving salt water or brine! Use with salt water or
brine will void warranty.
SPECIFICATIONS
Power supply required ........................115V, 60 HZ.
Horsepower ........................................................1/2
Motor duty .............................................Intermittent
Liquid Temp. Range ...............32°F to 70°F(0°-21°C)
Individual Branch Circuit Required
GFCI Class A ..............................................15 Amps
Motor full load (maximum) .......................7.3 Amps
Discharge: Cast Iron Models...............1-1/2" FNPT
PERFORMANCE
GPH (LPH) AT TOTAL FEET (M)
5 Ft.
10 Ft.
(1.52)
(3.05)
4,200
3,830
(15,897L)
(14,497L)
GENERAL SAFETY
Electrically powered sump pumps normally give
many years of trouble-free service when correctly
installed, maintained, and used. However, unusual
circumstances (interruption of power to the pump,
dirt/debris in the sump, flooding that exceeds the
pump's capacity, electrical or mechanical failure in
the pump, etc.) may prevent your pump from func-
tioning normally. To prevent possible water damage
due to flooding, consult your retailer about a sec-
ondary AC sump pump, a DC backup sump pump,
and/or a high water alarm. See the
"Troubleshooting Chart" in this manual for informa-
tion about common sump pump problems and
remedies. For more information, see your retailer or
call Flotec customer service at 1-800-365-6832.
1. Know the pump application, limitations, and
potential hazards.
Risk of explosion. Do not use in
explosive atmospheres. Pump
water only with this pump. Failure to follow this
warning can result in personal injury and/or prop-
erty damage.
2. Disconnect power before servicing.
3. Release all pressure within system before servic-
ing any component.
4. Drain all water from system before servicing.
Risk of flooding. If a flexible dis-
charge hose is used, pump may
move when motor starts. If it moves far enough
so that switch hits side of sump, switch may stick
and prevent pump from starting.Make sure pump
is secured so it cannot move around in sump.
5. Secure discharge line before starting pump. An
unsecured discharge line will whip, possibly
causing personal injury and/or property damage.
6. Check hoses for weak or worn condition before
each use, making certain all connections are secure.
For parts or assistance, call Flotec Customer Service at
15 Ft.
20 Ft.
(4.57)
(6.09)
2,720
950
(10,295L)
(3,596L)
7. Inspect sump, pump and system components
monthly. Keep free of debris and foreign
objects. Perform routine maintenance as
required.
Risk of Fire. Do not store or
rest objects on or near motor
or switch linkage. Keep all flammable objects
or liquids away from motor.
8. Provide means of pressure relief for pumps
whose discharge line can be shut-off or
obstructed.
9. Personal Safety:
a. Wear safety glasses at all times when work-
ing with pumps.
b. Keep work area clean, uncluttered and
properly lighted – replace all unused tools
and equipment.
c. Keep visitors at a safe distance from work
area.
d. Make workshop child-proof – with padlocks,
master switches, and by removing starter
keys.
10. When wiring an electrically driven pump, fol-
low all electrical and safety codes, as well as
most recent National Electrical Code (NEC) and
Occupational Safety and Health Act (OSHA).
11. This equipment is only for use on 115 volt (sin-
gle phase) and is equipped with an approved 3-
conductor cord and 3-prong, grounding-type
plug.
To reduce risk of electric
shock, be certain that it is
connected to properly grounded, grounding-
type receptacle.
• Never connect green (or green and yellow)
wire in cord to a live terminal!
• Where a 2-prong wall receptacle is encoun-
tered, it must be replaced with properly
grounded 3-prong receptacle installed in
accordance with the National Electrical
Code and local codes and ordinances.
12. All wiring should be performed by a qualified
electrician.
13. Make certain that power source conforms to
requirements of your equipment.
14. Protect electrical cord from sharp objects, hot
surfaces, oil, and chemicals. Avoid kinking
cord. Replace or repair damaged or worn cords
immediately.
15. Do not touch an operating motor. Modern
motors are designed to operate at high temper-
atures.
16. Do not handle pump or pump motor with wet
hands or when standing on wet or damp sur-
face, or in water.
Risk of Shock. If your basement
has water or moisture on floor, do
not walk on wet area until all power has been
turned off. If shut-off box is in basement, call elec-
tric company to shut-off service to house, or call
local fire department for instructions. Remove pump
and repair or replace. Failure to follow this warning
can result in fatal electrical shock.
1-800-365-6832
3