Installation And Electrical Connection; Description And Function; Product Description - Wilo Helix V 10 Instrucciones De Instalación Y Funcionamiento

5.4 Accessories
Original accessories are available for HELIX range:
Designation
1-1/4" 304 StS Counter Flange Kit (2x)
2" 304 StS Counter Flange Kit (2x)
2.5" 304 StS Counter Flange Kit (2x)
3" 304 StS Counter Flange Kit (2x)
Bypass kit 360 PSI
Bypass kit (with pressure gauge 360 PSI)
Baseplate with dampers for pumps up to 7.5 HP
The use of new accessories is recommended.

6. Description and function

6.1 Product description

FIG. 1
1 - Motor connection bolt
2 - Coupling guard
3 - Mechanical seal
4- Hydraulic stage casing
5 - Impeller
6 - Pump shaft
7 - Motor
8 - Coupling
9 - Lantern
10 - Tube liner
11 - Flange
12 - Pump housing
13 - Base plate
FIG. 2, 3
1 - Strainer
2 - Pump suction valve
3 - Pump discharge valve
4 - Check valve
5 - Drain + priming plug
6 - Air bleed screw + Filling plug
7 - Tank
8 - Foundation block
10 - Lifting hook
6.2 Design of product
• HELIX pumps are vertical high pressure non-self prim-
ing pumps with inline connection based on multistage
design.
• HELIX pumps combine use of both high efficiency
hydraulics and motors.
• All metallic parts in contact with water are made of
stainless steel.
• For models equipped with heaviest motor (>88 lbs),
a specific coupling allows to change the seal without
removing the motor. A cartridge seal is then used in
order to ease maintenance.
• Special handling devices are integrated in order to facili-
tate pump installation (Fig. 7).
WILO SE 01/2017

7. Installation and electrical connection

Installation and electrical work in compliance with any
Article n o .
local codes and by qualified personnel only.
2770484
WARNING! Bodily injury!
2770485
Existing regulations for the prevention of accidents must
2770486
be observed.
2770487
WARNING! Electrical shock hazard!
4146786
Dangers caused by electrical energy must be excluded.
4146788
7.1 Commissioning
4157154
Unpack the pump and dispose of the packaging in an
environmentally-responsible manner.
7.2 Installation
The pump must be installed in a dry, well-ventilated and
frost-free place.
CAUTION! Possible damage of the pump!
Dirt and solder drops in to the pump body can effect the
pump operation.
• It is recommended that any welding and soldering work
be done before installing the pump.
• Thoroughly flush the system out before
installing the pump.
- The pump must be installed in an easily accessible posi-
tion to facilitate inspection or replacement.
- For heavy pumps, install a lifting hook (Fig. 2, item 10)
above the pump in order to ease its disassembly.
WARNING! Risk of accident by hot surfaces!
The pump must be positioned so that someone cannot
come into contact with the hot pump surfaces while
operation.
- Install the pump in a dry place protected from frost, on
a flat concrete block using appropriate accessories. If
possible, use an insulating material under the concrete
block (cork or reinforced rubber) to avoid any noise and
vibration transmission into the installation.
WARNING! Risk of fall!
The pump must be correctly screwed to the ground.
- Install the pump in a dry and frost-free place on a flat
concrete block using appropriate accessories. If possible,
use an insulating material under the concrete block (cork
or reinforced rubber) to avoid any noise and vibration
transmission into the installation.
CAUTION! Risk of parts inside the pump!
Take care to remove closure members of the pump
housing before installation.
NOTE: Each pumps could be tested regarding hydraulic
features in factory, some water may remain in them. It
is recommended for hygienic purposes, to carry out a
rinsing of the pump before any using with potable water
supply.
- The installation and connection dimensions are given §
5.2.
English
11