Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
rewinding spool from Bulk Line
(use only .065 in. ROUND diameter line) (figs. Q, R, and S)
Bulk line is also available for purchase from your local
retailer. noTE: Hand wound spools from bulk line are likely
to become tangled more frequently than Black & Decker
factory wound spools. For best results, factory wound
spools are recommended.
To install bulk line, follow the steps below:
f Remove battery from tool.
f
f Remove the empty spool from the tool as described in
f
"replacing the spool".
f Remove any remaining cutting line from the spool.
f
f Make a fold at the end of the cutting line at about 3/4
f
inch (19mm)(22). Feed the cutting line into one of the
line anchoring slots (23) as shown in fig. Q.
f Insert the 3/4 inch (19mm) end of the bulk line into the
f
hole (24) in the spool adjacent to the slot as shown in
fig. r.
f Wind the cutting line onto the spool in the direction of
f
the arrow on the spool. Make sure to wind the line on
neatly and in layers. Do not crisscross (fig. s).
f When the wound cutting line reaches the recesses (25),
f
cut the line (fig. r).
f Fit the spool onto the tool as described in
f
"replacing the spool".
MAInTEnAncE
Warning! To avoid serious injury, remove the battery
from the tool before performing any maintenance.
1. Keep the air intake slots clean to avoid overheating.
2. Your trimmer line can dry out over time. To keep your line
in top condition, store spare pre-wound spools or bulk
line in a plastic, sealable bag with a tablespoon of water.
3. Plastic parts may be cleaned by using a mild soap and
a damp rag.
4. The line cutter on the edge of the guard can dull over
time. It is recommended you periodically touch-up the
sharpness of the blade with a file.
Important! To assure product sAFETY and rELIABILITY,
repairs, maintenance and adjustment should be performed
by authorized service centers or other qualified service
organizations, always using identical replacement parts.
Tool runs slowly
f Remove battery from tool.
f
f Check that the spool housing can rotate freely. Carefully
f
clean it if necessary.
f Check that the cutting line does not protrude more than
f
approximately 5-3/8 inches (136mm) from the spool. If
it does, cut it off so that it just reaches the line trimming
blade.
Automatic Line Feed does not Work
f Remove battery from tool.
f
f Remove the spool cap.
f
f Pull the cutting line until it protrudes approximately
f
5-3/8 inches (136mm) from the spool. If insufficient
cutting line is left on the spool, install a new spool of
cutting line.
f Ensure that the line is not crisscrossed on the spool
f
as detailed in figure 17. If it is, unwind the cutting line,
then wind it back on the spool neatly so that the lines
do not cross.
f Push the spool onto the housing until it snaps securely
f
into place.
f Align the tabs on the spool cap with the cut outs
f
in the housing.
f If the cutting line protrudes beyond the trimming blade,
f
cut it off so that it just reaches the blade.
If the automatic line feed still does not work
or the spool is jammed, try the following suggestions:
a. Carefully clean the spool and housing.
b. Remove the spool and check if the lever in the spool
housing can move freely.
c. Remove the spool and unwind the cutting line, then
wind it on neatly again.
d. Replace the spool into the housing.
ProTEcTInG THE EnVIronMEnT
Separate collection. This product must not be
disposed of with normal household waste. Should
you find one day that your Black & Decker product
needs replacement, or if it is of no further use
to you, do not dispose of it with household
waste. Make this product available for separate
collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces
the demand for raw materials. Local regulations
may provide for separate collection of electrical
products from the household, at municipal waste
sites or by the retailer when you purchase a new
product.
sErVIcE InForMATIon
Black & Decker offers a full network of company-owned and
authorized service locations. All Black & Decker Service
Centers are staffed with trained personnel to provide
customers with efficient and reliable power tool service. For
more information about our authorized service centers and if
you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location
nearest you, or visit us at www.Blackanddecker-la.com
EnGLIsH • 25
Publicidad
Tabla de contenido
