Product Familiarisation; Intended Use; Unpacking Your Tool; Before Use - Silverline 262212 Manual De Instrucciones

GB

Product Familiarisation

1 Column
2 Motor
3 On/Off Switch
4 Pulley Cover
5 Drilling Depth Gauge
6 Chuck Guard
7 Chuck
8 Spindle Pulley
9 Motor Pulley
10 Drive Belt Tension Adjuster
11 Plunge Handles
12 Table Locking Handle
13 Table
14 Base
15 Base Holes
16 Table Tilt Angle Scale
17 Table Tilt Bolt (hidden)
18 Spline Sleeve
19 Bearings
20 Spindle Sleeve
21 Spindle
Accessories included:
Hex key & chuck key
6

Intended Use

Bench mounted vertical drill for drilling a wide range of materials excluding most
masonry materials. Enables precise control of depth, hole position and angle entry into
the workpiece. Provides a stable platform when using accessories compatible with a
normal chuck.

Unpacking your Tool

Carefully unpack and inspect your tool. Familiarise yourself with all its features and
functions. Ensure that all parts of the tool are present and in good condition. If any parts are
missing or damaged, have such parts replaced before attempting to use this tool

Before Use

WARNING: Ensure the tool is disconnected from the power supply before attaching or
changing any accessories, or making any adjustments.
Assembling Your Drill Press
Tools required for assembly and operating (not included): Phillips screwdriver & Spanner
Note: This product will have traces of oil and grease on its component parts to protect
against corrosion. Clean off such residue before assembly especially the chuck mounting
and the internal fitting of the Chuck (7).
1. Secure the Column (1) to the Base (14) using the supplied bolts (x3), spring washers
(x3) and washers (x3) included. The spring washers fit between the bolt head and the
washer (Fig. I)
2. Slide the Table (13) on to the Column (1) and tighten the Table Locking Handle (12)
when approximately 150mm from the base (Fig. II)
3. Place the drill press head assembly on to the Column and lower it as far as it will go
Note: Seek assistance when handling the drill press head assembly as it is heavy.
4. When the head is aligned to the base, tighten the 2 hex grub screws which hold the
drill press head assembly in place with the supplied Hex key (Fig. III). These hex grub
screws are directly below The Drive Belt Tension Adjuster (10) on the same side
5. Screw the three Plunge Handles (11) into the Plunge Handles mounting (Fig. IV)
6. The chuck fits using a simple Morse taper connection and relies on the friction of the
surfaces to hold the chuck in position. Fit the chuck to the chuck mounting by placing
a small piece of wood below the chuck and operate the Plunge Handles to lower the
chuck mounting to fit the Chuck (Fig. V). You can alternatively fit the chuck before
mounting the drill press head assembly on the column. If necessary use a soft mallet
to help secure the Chuck but only use light force
Note: It is essential both surfaces are free of oil and grease for the chuck to be secure.
Note: Make sure the chuck jaws are recessed before striking the chuck with a mallet.
7. Angle the Chuck Guard (6) so you can remove the screws (x3), washers (x3) and nuts
(x3) that are pre-fitted to the chuck guard that will secure the chuck guard visor. Fit
the visor (Fig. VI) and then loosely re-assemble the screws, washers and nuts in each
hole. Ensure the visor position is correct then tighten the fittings.
8. It is important to secure the drill press to a work surface to prevent the tool tipping
over. Fit bolts and nuts (not provided) through the Base Holes (15) and matching holes
through a work surface to secure the drill press
Note: Use nylon insert lock nuts or spring washers in the fixings to prevent vibration from
loosening the fixings.
Note: If you don't secure the drill permanently it is recommended to use clamps to secure
the tool to a work surface or work only with material too small to cause the drill to tip over.
Adjusting speed
IMPORTANT: The drill may need adjustment of the Drive Belt Tension Adjuster (10) before
use even if you use the gear already set.
Belt Position Speed
(min )
-1
8 9 580
8 9 850
8 9 1220
8 9 1650
8 9 2650
• The drill has 5 speeds which are manually set. See chart below showing belt positions
for each speed plus an approximate speed guide for type and size of drill bit.
Spiral Brad- Forstner
drill bit point bit (wood)
(metal) drill bit
(wood)
11 - 13mm >25mm 35 - 50mm
8 - 10mm 25mm 28 - 32mm
5 - 7mm 20mm 19 - 25mm
3 - 4mm 3-15mm 13 - 16mm
1-2mm <16mm