Publicidad
Idiomas disponibles
Idiomas disponibles
Ref. Description
Contents
1
Plug & play harness
2
Sticky wired led 35 cm
3
7,5A fuse
4
Fixing bi-adhesive tape 70x55x3 mm
5
Tie rap 141 mm
6
Installation instructions
Ref. Description
Tools
1
Screw driver PH3 / PH2
2
Cutting nipper
3
Ratchet
4
Hexagonal socket 10mm
5
SUZUKI Service manual
Please read this manual and follow its instructions carefully. To emphasize special information, the symbol and words
Important
CAUTION and NOTE have special meanings. Pay special attention to the messages highlighted by these signal words.
WARNING
Caution
Note
Installation of this SUZUKI ORIGINAL ACCESSORY must be performed only by an authorized SUZUKI dealer who has the proper tools and
experience to do the job correctly.
a) Park the motorcycle steady in a safe place.
b) Keep the ignition key removed.
c) Be sure not to damage any vehicle part.
d) Check that all the parts are contained in the kit as listed in "Contents" section.
e) Disconnect the battery negative pole
1. Installation
BURGMAN 125 / 200 (UH 125 / 200)
a) Dismount the front leg shield including the headlights (follow chapter 8 of the service manual).
b) Insert deeply the 18-pin harness connector in the alarm unit up to the security catch is clicking.
c) Adjust the wire length by using delivered tie raps as shown in pict.1
d) Clean carefully the unit mounting area (pict. 2) and the bottom side of the alarm unit with a suitable cleaner.
e) Mount the alarm unit with the bi-adhesive tape as indicated in pict. 1 and press them for a few seconds.
f)
Connect the 1-pin connector (pict. 3
g) Identify the 13-pin turn indicators connector (yellow plug pict. 3
h) Identify the "SIDE STAND RELAY" (wire colour: green; orange/yellow; orange/black; orange/yellow) (pict. 4
harness counterparts.
i)
Place the LED as indicated in picture 5
j)
Connect the LED 2-pin connector to the plug&play harness counterpart.
k) Route the wires of the harness and secure them with tie raps "5".
l)
Remount the front leg shield and the negative battery pole.
m) Check and test the system (point 2).
BURGMAN 400 (AN 400)
a) Dismount the wind shield, the meter panel; front leg shield including the headlights (follow chapter 9D of the service manual).
b) Insert deeply the 18-pin harness connector in the alarm unit up to the security catch is clicking.
c) Adjust the wire length by using delivered tie raps as shown in pict.6
d) Clean carefully the unit mounting area (pict. 7) and the bottom side of the alarm unit with a suitable cleaner.
e) Mount the alarm unit with the bi-adhesive tape as indicated in pict. 7 and press them for a few seconds.
f)
Connect the 1-pin connector (pict. 8
g) Identify the 13-pin turn indicators connector (yellow plug pict. 8
h) Identify the "SAFETY RELAY" (wire colour: yellow/green; yellow/black; white/black; black/white) (pict. 9
counterparts.
i)
Place the LED as indicated in picture 10
j)
Route the wires of the harness and secure them with tie raps "5".
k) Remount the wind shield, the meter panel; front leg shield and connect the LED 2-pin connector to the plug&play harness counterpart during
remounting.
l)
Reconnect the negative battery pole.
m) Check and test the system (point 2).
2
Indicates potential hazard that could result in death or injury.
Indicates potential hazard that could result in vehicle damage.
Indicates special information to make maintenance easier or Instructions clearer.
Caution – Preparation before Installation
A) (+12V) to the plug&play harness counterpart.
D.
E) (+12V) to the plug&play harness counterpart.
H.
SUZUKI GENUINE ACCESSORIES
Q.ty
1
1
1
1
8
1
(1)
(2)
Caution
B). Interpose the plug&play harness counterparts
F). Interpose the plug&play harness counterparts
(3)
(4)
C) and interpose the plug&play
G) and interpose the plug&play harness
(5)
WARNING,
Publicidad
