Parameter Setting And Display; List Of Parameters - Sime Brava Slim HE 25/55 ErP Manual De Instalación Y Mantenimiento

3.3

Parameter setting and display

To go into the parameter menu:
– from the selected mode (eg. WINTER)
– press the buttons r and
the same time until "PAR 01" (parameter number) and the
value set (0÷4) appears on the display
– press the button t to scroll up the list of parameters and
then r to scroll down the list
3.4

List of parameters

Type No. Description
Index showing boiler power in kW
0 = 25T
PAR 01
1 = 25/55
3 = 30/55
Hydraulic configuration
0 = rapid
1 = storage tank with thermostat or heating only
2 = hot water tank with sensor
PAR 02
3 = bithermic
4=instant with solar power input
5 = open vent
6 = boiler with heat pump
Gas Type Configuration
PAR 03
0 = G20; 1 = G31
Combustion configuration
PAR 04
0 = sealed chamber with combustion control
PAR 08 External sensor value correction
PAR 09 Ignition fan speed
PAR 10 Boiler Antifreeze Threshold
External Sensor Antifreeze Threshold
PAR 11
-- = Disabled
PAR 12 Heating Curve Incline
PAR 13 Minimum Heating Temperature Adjustment
PAR 14 Maximum Heating Temperature Adjustment
PAR 15 Maximum power heating
PAR 16 Heating Post-Circulation Time
PAR 17 Heating Pump Activation Delay
PAR 18 Re-ignition Delay
Domestic Hot Water Modulation with Flow meter
PAR 19 0 = Disabled
1 = Enabled
PAR 20 Maximum power domestic hot water
PAR 21 Minimum power heating/domestic hot water (premixed)
Domestic hot water preheating enabling
PAR 22
0 = OFF; 1 = ON
External relay 1 function
0 = not used; 1 = remote alarm NO; 2 = remote alarm NC; 3 = zone valve; 4
PAR 23
= automatic filling; 5 = external request; 6 = recirculation pump; 7 = zone
valve with OT; 8 = relaunch pump; 9 = boiler with heat pump (circulator)
88
t (for approximately 5 seconds) at
DOMESTIC HOT WATER - HEATING
holding the buttons
NOTE:
scrolling movement.
– once the required parameter has been reached, press the
buttons > or < to modify the value within the permitted range.
The modifications are stored automatically.
When all the parameter modifications have been made, exit the
parameter menu by pressing and holding down the buttons
and t
all at the same time
screen is displayed.
CONFIGURATION
80 .. 160
0 .. +10
20 .. PAR 14
PAR 13 .. 80
0 .. 100
0 .. 100
0 .. 100
r or t increases the speed of the
for at least 5 seconds until the initial
Range U/M Step
0 .. 4 - 1
0 .. 6 - 1
0 .. 1 - 1
- - -
-5 .. +5 °C 1
RPMx25 1
°C 1
-9 .. +5 °C 1
0 .. 80 - 1
°C 1
°C 1
% 1
seconds
0 .. 99 1
x 10
seconds
0 .. 60 1
x 10
0 .. 60 Min 1
0 .. 1 - 1
% 1
% 1
0 .. 1 - 1
0 .. 9 - -
EN
r
Default
1 or 3
2
0
0
0
128
3
-2
20
20
80
100
3
0
3
1
100
0
0
0