Unscheduled Maintenance; Possible Faults And Solutions - Sime Brava Slim HE 25/55 ErP Manual De Instalación Y Mantenimiento

EN
4.5

Unscheduled maintenance

If replacing the electronic board , the user MUST set the
parameters as indicated in the table.
Type No. Description
Index showing boiler power in kW
0 = 25T
PAR 01
1 = 25/55
3 = 30/55
Hydraulic configuration
0 = rapid
1 = storage tank with thermostat or
heating only
PAR 02 2 = hot water tank with sensor
3 = bithermic
4=instant with solar power input
5 = open vent
6 = boiler with heat pump
Gas Type Configuration
PAR 03
0 = G20; 1 = G31
To enter "Parameter setting and display"refer to the indications
provided in the specific section.
Once the parameters in the table have been set, you must carry
out the entire phase of "Self-calibrating procedure" described
in the specific section.
If the gas valve and/or the ignition/detection electrode , and/or the
, and/or the fan are replaced, the user must still carry out
burner
the entire phase of "Self-calibrating procedure" described in
the specific section.
4.6

Possible faults and solutions

LIST OF MALFUNCTION/FAULT ALARMS
Type No. Fault
Low water pressure
ALL 02
in system
High water
ALL 03
pressure in system
Domestic hot water
ALL 04
sensor fault
Delivery sensor
ALL 05
fault
ALL 06 No flame detection
Sensor or safety
ALL 07 thermostat
intervenes
Fault in the flame
ALL 08
detection circuit
No water
ALL 09 circulating in the
system
Setting
1 or 3
2
0 or 1
Solution
- Restore pressure
- Check for any leaks in the
system
- Empty the system via the
drain valve on the hydraulic
assembly and bring the
pressure to approximately
1.2 bar
- Check connections
- Replace the sensor
- Check connections
- Replace the sensor
- Check the integrity of the
electrode and check that it is
not grounded
- Check gas availability and
pressure
- Check the integrity of the gas
valve and the card
- Check the sensor or
thermostat connections
- Deaerate the system
- Check the bleed valve
- Replace the sensor or the
thermostat
- Check that the pump
impeller is not blocked
- Check the integrity of the
electrode and check that it is
not grounded
- Check gas availability and
pressure
- Check the integrity of the gas
valve and the card
- Check the rotation of the
pump rotor
- Check the electrical
connections
- Replace the pump
Type No. Fault
Auxiliary sensor
ALL 10
fault
Gas valve modulator
ALL 11
disconnected
Incorrect
configuration of
ALL 12
the open /sealed
chamber
Smoke probe
ALL 13
intervention
ALL 14 Smoke probe fault
Fan check cable
ALL 15
disconnected
Condensate level
ALL 18
fault
Maximum number
ALL 28 of consecutive
resets reached
Return sensor (SR)
ALL 30
fault
Fault due to low
ALL 37
network voltage.
Incorrect network
ALL 40
frequency detected
Flame loss more
ALL 41 than 6 consecutive
times
ALL 42 Button fault
Open Therm
ALL 43 communication
fault
Self-calibrating
ALL 62 procedure is
required
Incorrect
ALL 72 positioning of the
delivery sensor
EV2 SGV current
ALL 77 max/min absolute
limits error
EV2 SGV current
ALL 78
upper limit error
EV2 SGV current
ALL 79
lower limit error
Fault on the valve
control logic
ALL 80
line/valve cable
damaged
Block due to
ALL 81 combustion during
start-up
Block due to
numerous
ALL 82
combustion control
failures
Solution
- Check PAR 02 "hydraulic
configuration"
- Check the electrical
connection
- Check the electrical
connection
- Set the parameter PAR 04
(Combustion configuration)
to 0
- Replace the smoke probe
- Contact the Technical
Assistance Centre
- Replace the smoke probe
- Check the electrical
connection of the smoke
probe, if the problem is
not resolved, contact the
Assistance Centre
- Check the connection cable
between the fan and the
board
- Check for any clogging in
the pipe which takes the
condensate to the siphon
- Check that the siphon is not
clogged
- Contact the Technical
Assistance Centre
- Replace the return probe
- Contact the Technical
Assistance Centre
- Check with tester
- Contact network provider
(ENEL)
- Contact network provider
(ENEL)
- Check the detection
electrode
- Check the gas supply (open
valve)
- Check mains gas pressure
- Check that buttons are
working
- Check the electrical
connection of the remote
control
- Carry out the self-calibrating
procedure (see the specific
section)
- Check that the delivery
sensor is attached to the
delivery pipe
- Contact the Technical
Assistance Centre
- Contact the Technical
Assistance Centre
- Contact the Technical
Assistance Centre
- Check the valve cable
- Contact the Technical
Assistance Centre
- Check for blockage in
chimney
- Bleed the air from the gas
circuit
- Check electrode
- Check outlets
95