Assignment Of Internal Fault 999 - baltur BT 320 Guía Rápida

4 ASSIGNMENT OF INTERNAL FAULT 999

0-1999 internal faults generated from within System apI
D1 D2
10 return value of m_PwrOn_uiInitAPI()
20 0
21 0
22 Erroneous State
40 0
92 Directive
200 0
201 0
202 0
203 0
204 0
210 sEECtrl.sChk.uiReadStartAddr
211 sEECtrl.sChk.uiReadStartAddr
212 sEECtrl.eSeq_State
215 uiEEFaultAddr
216 uiEEFaultAddr
217 uiEEFaultAddr
220 0
222 uiEEStartAddr
240 uiEEStartAddr
241 uiEEStartAddr
242 uiEEStartAddr
243 uiEEStartAddr
244 ulReqFIFOSpace
250 (ulong32)pucDst
300 0
301 0
350 0
360 0
361 0
380 uiBPP_HPPunktNr
381 0
382 0
383 uiBCP_AnzParam[0]
384 uiBCP_AnzParam[1]
385 sRx.Buffer.ui[ucRxOk-1][uiSTART-
BEF+47]
386 uiParaIdx
410 sIO.sIn.ulInputsN
411 input status received from UP
412 0
420 uil
430 ucPin2Test
431 ucPin2Test
440 0
m_PwrOn_uiInitAPI() failed
CRC32 check of ROM failed
Cyclic CRC32 check of ROM during runtime failed
State machine for CRC32 check during runtime ran into an invalid state
m_PwrOn_bLoadEEPROM() failed
ATTENTION, wrong number in the wrong module, signaled by hchactab if control
tables are not correct
Last destination element is no member of sER.sP
Last destination element is no member of sER.sM
Last destination element is no member of sER.sC
Last destination element is no member of sER.sH
Destination is no member of sER.sX
Refresh cycle timeout expired
Uncorrectable error in EEPROM block
Invalid state
Uncorrectable error in Parameter Set
Uncorrectable error in Miscell-Data
Uncorrectable error in Curve Set
pucDst == NULL
Invalid EEPROM address
Write beyond end of safety area!
Start address in safety area is no multiple of 3
Write beyond end of non-safety area!
Start address is in reserved area!
Not enough FIFO space
Readback error while refreshing - possibly defective RAM cell
Timout sICom.uiRxLiveTimer expired
Timout sICom.uiRxLiveTimer expired
Timeout sICom.uixLiveTimer expired
Timeout while waiting for the exit from DUAL_BEF_CHECk_PARAM
FIFO ful !
Error while calling uiPutPunkt()
Seal control command in the presence of BM_FAT_kALTCHECk
Timeout in the cyclical parameter comparison
DUAL_BEF_CHANGE_PARAM1: Invalid value in the reception buffer
DUAL_BEF_CHANGE_PARAM2: Invalid value in the reception buffer
Cyclic parameter verification: different parameters between HP and UP!
PowerOn parameter verification: different parameters between HP and UP!
Detected positive half-wave on terminal input!
Different input status between controllers
The readback input of the fuel selection relais contacts in the dual fuel is invalid. DFM
probably defect.
Input status of digital input on HP and UP is inconsistent (>20ms)
Pin short circuit test detected an error!Currently tested pin not configurated as output
or is stuck at 1
Pin short circuit test detected an error!Short-circuit between pins, pull-up of input stage
defective or pin is externally stuck at 0
sIO.sIn.uiTestSignalTimeout expired
41 / 50
0006081511_201311
Description